Having problems with your AEG 24 in. Favorit 86050Vi Built-in Dishwasher ?

Our AEG Favorit Sensorlogic Turbodryis conected to cold water.(2005 Model) It does not heat the water ..or dry. The whole washing prosess is Cold.


Answers :

I have the same problem, i have a machine that is 2005 model and it does not heat the water or dry in the end
Your problem is the in-line heating element. Mine had the same thing wrong with it. The element is actually a common type used in several types of machines, AEG, simpson etc. and is therefore easy to get a spare for. About A$75 from a white goods spare part distributor.
It is also easy to replace and the first part behind the rear access plate.
Unplug machine.
Pull the machine out and remove the 2 screws holding the lower access plate at the rear (you will need a TORX type screw driver).
you will see the element below;

11_20_2012_1_52_19_pm.jpg
The ends are connected to two pipes, there is also an earth wire (green) and a small plug with 2 wires.
Disconnect all, and remove.
The elements come in two types based on the pipe size, a 40mm, and a 32 mm. Mine was 32.
Simply swap for new element.
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 86050Vi Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our AEG Favorit Sensorlogic Turbodryis conected to cold water.(2004 Model) It does not heat the water ..or dry. The whole washing prosess is Cold.


... Dishwashers

Our AEG Favorit Sensorlogic Turbodryis conected to cold water.(2005 Model) It does not heat the water ..or dry. The whole washing prosess is Cold.


I have the same problem, i have a machine that is 2005 model and it does not heat the water or dry in the end ... AEG 24 in. Favorit 86050Vi Built-in Dishwasher

Do these 'portable' dishwashers 'heat' water prior to washing? i have customer complaining bout the dishes not coming clean..yet the water entering the dishwasher is cold, does not appear to heat water prior to washing.


Most dishwashers require a minimum 120 degree inlet water temp. The heating element will boost this up during the main wash cycle to aprox 140. Do not hook a dishwasher up to inlet water temps above 150. ... GE Hotpoint HDA3500N Dishwasher

I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?


... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher

Hiya, I have a Bosch Dishwasher SGV4313GB that wont heat the water, it gets stuck with cold water continually washing (pre wash??) the delf. Its a built in and I have opened the inside metal panel and exposed the control unit (PCB) there is no blackened/loose soldered joint to be resoldered. I am at a loss as to what else in the heating circuit to look for. Can you point me in the direction of what I should look for next? Kind regards Mark


... Bosch Dishwashers

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

Hoover HND 625 does not heat the water(cold fill) and at the end of the programme leaves cold water in the machine. Pots not washed properly. If new programme is selected it empties water in first minute or so.


... Hoover Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

My swd60 hotponit dishwasher will not het the water and at the end of each wash the deilcates light is flasing, ive been tld it sould be connected to ho water supple, but when i got is was put on cold and heated he water fine. pls help


Hello mam please change the heating element of the dishwaswer. ... Dishwashers

Indesit idl 535, washing on usual cycle but not heating and dishes not being cleand properly? Disolves tablet and goes through full wash cycle as usual but doesnt wash dishes properly and the dryer isn't working as it normally is hot when you open the door, but it is just cold. water draining as normal too.


Your problem is very clear, you need to replace the wash tank heating element. ... Indesit 24 in. IDL500 Built-In Dishwasher

Indesit dishwasher The water does not heat up so the dishes are being washed in cold water and then they are not being dried... Anybody know what the problem is and if it will be expensive to fix.. Thanks


Element gone. approx 40 quid for element and 30 to fit it. ... Indesit 24 in. D61 Free-standing Dishwasher

When dishwasher is plumbed in to cold water, what temperature does the dishwasher heat the water to when washing the dishes?


... Fisher and Paykel Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

Hi, My westinghouse dishwasher SB907 goes through the washing cycle but doesn't seem to heat up and use the hot water. I have changed the little switch thing, that costs around $20, so what else cold be the problem?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Dishwashers

We have a DX 303 dishwasher that suddenly has stopped washing dishes with any heat. Water is cold and dry time does nothing. Opening at end of time doesn't result in steam shower like normal


... Electrolux Dishwashers

Dishwasher not heating up.just got cold water wash.


NTC fault or heater open circuit. Electronic might not be sending power to element too. You would have to work through this one with some expertise. Better call a technician.... ... Dishwashers

Dishwasher not drying dished with any heat source. Dishes washed in cold water.


Most dishwashers are plumbed to the hot side of the hot water side of the faucet. This should provide hot water for washing the dishes. Perhaps this dishwasher was plumbed to the cold water side by mistake.Most dishwashers have a heating ... Dishwashers

My built in Tecnik dishwasher is not heating the water so that it in effect does a cold wash that seems to take all night before reaching the end of the program. Have tried reset, to no avail.


You really need to change or check heating element assy.... ... Tecnik 24 in. TKD795/3 Built-in Dishwasher

Hi there I have a Zanussi zdf121 dishwasher which is only doing a cold wash, not heating at all. Not sure if its hot fill but the hot water is fine elsewhere. Any ideas please Pete


Do you have it hooked up to hot or cold water supply? Most residential dishwashers don't come equipped with a booster heater. If it's connected to the cold side, you'll have to replace the angle stop with a single outlet stop and replace the hot an ... Zanussi 18 in. DA4342 Free-standing Dishwasher

The water in the dishwasher is always cold with no heat so a poor wash. Does the dishwasher have a built in heater element?


... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Glasses have a film after washing complete. No food particles, just heavy film. I suspect dishes are the same, but doesn't show as much. Water temperature entering washer is 130 degrees. Heating element heats during drying cycle---not sure during wash cycle. Sounds like a good water spray during washing cycle.


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty ... Frigidaire 24 in. FDB421RF Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1748 seconds