Having problems with your AEG Dishwashers ?

Dishwasher Model DE-56SS about 8 years old does not drain water between wash cycles or at the end of a wash.Nothing seems to be pluged in the drain hose or the drain. Is it the drain pump or some senor. What would be the cost of parts to fix this problem.


Answers :

Repair Help & Product Troubleshooting for AEG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher Model DE-56SS about 8 years old does not drain water between wash cycles or at the end of a wash.Nothing seems to be pluged in the drain hose or the drain. Is it the drain pump or some senor. What would be the cost of parts to fix this problem.


... AEG Dishwashers

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Same problem Hi, I have the same problem there is water in the filter basket of the dishdrawer, I have watched the draining process when itgoes to error F1 and there seems to be a cycle of draining then pushing the water back through again. I have checked for blockages as advised above with a wire, no blockage, I have also blown through the outlet hose to the drain and there is no blockage. I am thinking the blockage maybe in the contained section of the pump as the previous man has explained. T


Hi, \015\012Below is the service manual. Use the FU (fill water) function in the diagnostics and then use P2 to drain the water. Open the drawer and watch will testing.\015\012Good Luck\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

I own a build-in LG Stainless Dishwasher (modle: LDF1178ST). It stopped draining water during its recent startup due to its idle (no operation) for about a year:). I can only feel the hose full of water by touching the drain hose between the washer and the sink desposal. It's hard to check other part of dish washer since it's built in our cabinet. Could any dishwasher expert help to advise how to trouble shoot or fix this problem. Thanks, Alex Chen 571-220-7484


There is a float in the bottom of the dishwasher that tell the motor to turn on and pump out the water. I would check the float first to see if it is hung up and not raising to tell the dishwasher that there is water in the base. Check the check valv ... LG Dishwashers

I'm having problems with the drain pump constantly running. I understand so far that it'll be the anti-flood device that is causing this. I've taken the dishwasher out and tipped it backwards to drain as much water out as possible but nothing comes out from anywhere ! It appears to be a sealed unit so how do I get to the appropriate part and fix it ? Cheers !


... Neff 24 in. S5453X1 Built-in Dishwasher

I have a Kenmore dishwasher model #665.13842K601. The problem that it has is that it does not seem to be pumping the water around the tub after it fills. It will fill and drain fine but will not wash. I have removed the spray arms and checked all the parts that I can get to from the inside but fear that it may be a pump or jammed impeller. it does make a faint buzzing sound when it should be operating. Any input would be great. Thanks, Matt


It sounds like you have a circulation problem which means that the circulation pump has gone bad. \015\012Circulation pump - http://www.appl ... Kenmore Dishwashers

Asko 1375 unit will not wash drains and fills ok  motor at back of unit runs well. Suspect impeller   Does motor have to come off for impeller replacement?? My 1375 is leaking a bit, looks like the seal which was mentioned in the impeller repair case,may be the problem? The other problem I noted was a clogged screen at the bottom of the dishwasher which is on the suction side of the pump, the screen had calcium buildup etc. I cleaned it off with vinigar and reran the dishwasher seemed ot fix th


Do you mean to say that the washer does not go into the wash cycle at all, or washes poorly?An answer to both can be found HERE.This article ... Asko 1375 Dishwasher

I have a Kenmore Quietguard dishwasher, only a few years old, and it won't drain. I pulled it out and checked the drain hose, could not find a clog. I took the basket and sprayer out, couldn't find any clogs there. It seems to be making a little bit of a different noise but does still clean the dishes. Does the motor pump the water out and could that be the problem?


I have a Kenmore Quietguard portable that won't stay connected to my kitchen sink faucet. Checked all I can and continues to spray the wall and me without staying attached securely to the faucet adapter. Help!! Any ideas? ... Kenmore 24 in. 15162 Built-in Dishwasher

I had a draining problem, clogged line, fixed. Does the small in line rubber valve under the dishwasher in the transition piece to the hose have any real need to go back? and which direction it is cupped slightly. Also are there any assembly instructions? I cant seem to get it back quite right, or a white washer has split. not sure which.


... Whirlpool 24" Built-In Dishwasher - Black-on-Black

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

I have a Jenn-Air JDB9910AWB dishwasher. The problem I am having is everything seems to work fine until the drain cycle. It sounds like the pump is frozen. After selecting the drain button you can hear a click in the control panel followed by a 1-2 second growl in the pump but it doesn't turn or pump. I am assuming the pump runs in reverse for draining? Is it safe to assume the pump is bad?


... Jenn-Air JDB9910 Dishwasher

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers

My GE Monogram ZBD4500 dishwasher does not drain completely at the end of the cycle. If I run a couple of manual cycles afterwards it eill eventually drain completely. Drain hose is clean, pump suction sump looks clean, drain pump impeller appears OK, discharge check valve assembly is easy to blow through in direction of drain. Do I have a sequence switch problem?


I bloody lostt you! are you still there? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Not draining Hey I have a whirlpool(model # DUB50DWGB1) and Ive hooked it up and it wont drain. Ive taken the filter off and checked the bottom hose and it drains. I think that it is the pump is not pumping up to the gargbage disposal. If the gargbag disposal is not hooked up, would that be my problem? Thanks for any help taht you can give


Hi and welcome to Fixya, \015\012 \015\012I'd suggest you are correct in your suspicsion of the disposer being a likely problem. \015\012 \015\012Start by checking the drain spout of the dispose ... Whirlpool Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

I have a Bosch Dish Washer M# SHV4803UC/U12. The D/W presented itself with a slow drain,proved by disconnecting the drain hose from underneath the sink. I changed the pump, and the drain hose. The problem still exists, and nothing is caught in the line or the sump of the dishwasher. What can be my issue.


Try the diagnostics to check out the machine.\015\012\015\012To start test program, press and hold both POWER SCRUB PLUS and REGULAR WASH program buttons, then turn unit on by pressing ON/OFF button. When program buttons are release ... Bosch Dishwashers

Brown scum accumulates under the large circular aluminum plates on the bottom of the drawers. Has to be cleaned out every 1-2 weeks. We have never had a dishwasher that required so much maintenance. We think it is the size of the drain. Can this be fixed by installing a larger drain hose. We have cleaned out the drain hose and it doesn't stop the problem.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Won't drain Hi my dishwasher will turn on start running but cannot drain the water i checked the drain hose it is totally clear. People have suggested its something stuck in the pump but I can't seem to access the pump


To access the pump, first bail and sponge out any water in the machine's tub. Then tip the machine over on its front, using a heavy blanket or pad to protect the washer's finish. Remove the back service panel. \015\012The pump is attached to the moto ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1816 seconds