Having problems with your AEG Dishwashers ?

Aeg sensorlogic 50700 first showed c2 message; we drained & cleaned filters 3 times; worked half cycle and now showing error message c3?


Answers :

Error message C3 is most likely indicating the flood switch is triggered. This means water is leaking from under the sump. The C2 error is linked to drain problems which you cleared.
Repair Help & Product Troubleshooting for AEG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Aeg sensorlogic 50700 first showed c2 message; we drained & cleaned filters 3 times; worked half cycle and now showing error message c3?


Error message C3 is most likely indicating the flood switch is triggered. This means water is leaking from under the sump. The C2 error is linked to drain problems which you cleared. ... AEG Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

Zanussi ZDF 511 S dishwasher not draining. Shows error message '20'. Cleared filter, removed hose from usual drain and restarted cycle. Still not working - same error message. Any suggestions would be helpful. Thank you. Myles


... Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Hi . I have a Zanussi DE6965 which has started displaying the error message AL6 every now and then. When it stops and shows this the water has not pumped out. If you turn it off, leave for half an hour or so and turn back on it sometimes works fine to the end. Sometimes it stops again. Eventually after several stop starts it works through. Any advice what could be causing this? Thanks.


... Zanussi 24 in. DE6965 Built-in Dishwasher

My lxi dishwasher drains more water than it fills during a cycle so after about three cycles the water level becomes to low. No error messages come up but I have to turn it off and refill it all the time. water pressure at the machine guages shows about 20psi when rinsing


There are two different styles of lxis one style has a drain diverter valve probably messed up some how something stuck in it not diverting the water to the wash arms and instead pumping right down the drain I am guessing this is your problem.There i ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have had an E24 error message on my Siemens freestanding dishwasher. As well as the Error message the the little tap sign lights up too. Up until now the problem has occurred around 1 in 3 attempts and mainly at night but not in the day. When it does work the washer works perfectly and washes well. Today it will not work at all. The error always comes up 2 minutes into any cycle. I've tried turning the water feed off and on and in the past this has worked. It sounds like no water is gettin


Hi Steve\015\012\015\012E24 error normally indicates failure to drain, the first\015\012thing to check is that the water is actually being supplied to the appliance\015\012and is turned on. If it is then check the water inlet valve, if th ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

My Professional series model fdbb4365fc2 Makes a slight intermittant thumping sound a few times when its started and than after a few moments it shows the error code uo. For a while we could cancel and try a different cycle and it would work. I checked drain hoses and sink trap all looks o.k. What is my options


... Frigidaire Dishwashers

My ADP6000IX dishwasher has stopped working. Put it on a cycle and it has started beeping and coming up with an error message err 4. Have cleaned out filter and wiped inside. Don't have the manual to check what this means. Can you help?


... Dishwashers

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.


Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

I own the Siemans SL34A006UC dishwasher which had the recall repair completed. Now it doesn't work right. The unit goes through any of the cleaning choices but when it comes time to drain, the unit stops for a few seconds, swishes water for a couple seconds, stops again, then swishes for a couple seconds, stops and then goes back in to regular cleaning mode until the timer reaches zero. At each drain cycle, it does the same thing earlier mentioned 3 times in a row, then back to washing. The unit


You say "dishwasher which had the recall repair completed." (sic) "Now it doesn't work right" (sic)\015\012\015\012Being a professional I must advise,and that, if this is the case, th ... Dishwashers

I have a DD601 v2, the bottom draw starts up and pumps water in then pumps it out again immediately. No error codes are showing, it just shows the cycle time remaining but doesn't decrease from its start time.


I am assuming the drawer is showing this behaviour repeatedly even after your start fresh with power turned off and back on.\015\012\015\012Are you able to see any different behaviour with the shorter cycles in ECO mode?\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I bought a used GE Triton XL d/w with no manual. It worked great but now it is not cleaning anything, when the cycle is over the soap cup is open but half of the soap is still inside of the cup. I opened the d/w during a cycle and the dishes are wet top and bottom racks so I know it's getting water but the dishes are still filthy. Why is the soap not working? It's like water is spraying everywhere but the door where the cup is!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... GE Tritonr XL GSD6260JCC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2000 seconds