Having problems with your Amana 24 in. ADB1500AW Built-in Dishwasher ?

Power to the dishwasher, but I can not get it to work. The washer is only a year old. The lights come on, but it will not run. Is there any kind of a reset that I can't find?


Answers :

From your description it sounds like your control panel/keypad is bad. If you are getting lights when you choose a cycle but no response when you push start then you control panel is bad. \012
\012http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http://c.searspartsdirect.com/lis_png/PLDM/W0809152-00002.png\012
\012You need item#4 on that picture. That parts cost around $60 and you can find it at an appliance parts store. Changing out that piece should not be to difficult either. Just unscrew the inner door from the outer and disconnect the ribbon cable from the computer board. Install the new control panel and fasten the pieces back together and you have a working dishwasher. \012
\012Please rate me "4 thumbs" if this information was helpful.\012Wish you the very best!
Repair Help & Product Troubleshooting for Amana 24 in. ADB1500AW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Power to the dishwasher, but I can not get it to work. The washer is only a year old. The lights come on, but it will not run. Is there any kind of a reset that I can't find?


From your description it sounds like your control panel/keypad is bad. If you are getting lights when you choose a cycle but no response when you push start then you control panel is bad. \012 ... Amana 24 in. ADB1500AW Built-in Dishwasher

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

Ariston dishwasher i have an ariston built in dishwasher. It wont start washing cycle, and has 2 flashing lights from the left (total 4 lights)...can anyone help. i cant find the model number on the machine. The lights looking like sprinkiling water..i have filled the salt, and rise etc but still it wont come on please help


I have a brand new ariston ll-64 and the wash cycle won't start and two flashing lights ... Ariston Technologies L63 Free-Standing Dishwasher

I press the test button and red light goes out. I then press reset and the light comes on and washer won't run.


... Campbell Hausfeld PW1750 Electric Pressure Washer

My kenmore dishwasher 665.17052400 clean light is flashing 7 times. I cannot locate the tech sheet to find out what is wrong. I have reset the panel and it will run then blink again after 15 mins or so. I have also done a hard reset and looked at the heating element, but it looks fine. Please help.


... Kenmore Dishwashers

Kenmore quietguard 7 dishwasher...clean light flashing, dishwasher won't run repair guy a few weeks ago couldn't come, but told my husband to push a couple of the buttons on the control panel, and it worked for a while... repair guy coming back on Monday, but I''d like to know the buttons to push to reset it so I can use it till then


... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

My electric pressure washer's motor will not start. the 110 plug has a test/reset fuse on it. when i plug it in the light comes on. i push test- it turns off but motor does not run. i push reset and the light stays on.


With the water faucet turned fully on and the power switch on squeeze and hold the trigger for at least 10 seconds to let the water flow push the air out and then it should start up. ... Campbell Hausfeld PW1750 Electric Pressure Washer

I tried the steps listed at this website for the same issue I am having. http://www.fixya.com/support/t273954-kenmore_elite_dishwasher The steps worked to get the dishwasher to "reset" with all the lights coming on. The problem I am having now is that after the "reset" the dishwasher starts to run a small cycle for about 5 minutes. Upon opening the washer, nothing has happened inside (no water, no visible movement of parts, no soap container opening). Upon closing the dishwasher and trying


I think think the water fill is ok and the drain is ok as it uses a seperate drain motor . but what is not working is the main wash motor . so no water is moving and the wash arms are not going around and the lights ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Corroded ribbon cable on maytag mdbtt60aww some of lights work but unit will not run. cant find ribbon cable in parts list


... Dishwashers

My Kenmore model 665-16919001 control panel stopped lighting up, nothing will come on. I can't seem to find reset codes anywhwere. Can you help?


... Kenmore Dishwashers

I have a Kenmore dishwasher 665.16022402 that is locked out at the board.( the clean light flashes continually & wont allow it to run) I don't have the manual to find the reset code and troubleshoot. There didn't seem to be any proublems till now.??????? any help?


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a model MDB7100AWQ, it fills with water but the motot won't start. Is there a reset code for this model? I did find a melted off plastic spoon handle in the bottom, could this cause it to trip something in the unit? The lights on the door switches come on but it only clicks, and won't start.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To start with check the\015\012door switch if that\342\200\231s fine then you\342\200\231ll have to replace the ... Dishwashers

I have 3 lights on my panel that are blinking and i, cant get it run. what is the reset code sequence?


... KitchenAid KUDS30IVWH Builtin Dishwasher

When I press the on button the cycle light is on at the 50 degree setting and I cant change the setting and it wont run on that cycle. It has happened several times but this time it wont come around


Looks like micro controller problem. Contact authorized service center. ... Dishwashers

Kenmore 16604 In the middle of washing it stopped. No lights will come on and it appears to have no power. I checked the breaker, it's OK. All other appliances and circuits are working in the kitchen. Is there a reset button I can't find? Help!!


No reset button. Most likely, the thermal fuse went out. This happens if the water inside gets too hot. The thermal fuse is clipped to the electronic board behind the console. The heater thermostat is underneath the tub on the right side. The parts s ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Miele g892 and just like everyone the red light comes on and dishwasher stops running> why cant you answer thic common problem>


The red light tell you there is a fault. You have to read the fault code and it will give you a general idea of the problem - to do this you have to enter the service mode of operation - close the door and turn the dishwasher on. The Start/St ... Miele G880 Dishwasher

No Heat Had the blinking clean light problem, reset, and it fills and runs, but element not heating. Element reads 10.6 ohms, both door switches seem to be making. What else might be causing it not to heat? Is it possible to find a wiring diagram or schematic?


Should be a tech sheet stuck to inside of the bottom toe panel.Switches may check OK with no load applied. There is also an over temperature thermostat that may be open. If all checks OK, control may have failed. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i cant start the dishwasher unless i reset the dishwasher and then it does the same thing


Hi angelbme1,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i c ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1294 seconds