Having problems with your Amana 24 in. ADB1500AW Built-in Dishwasher ?

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


Answers :

Repair Help & Product Troubleshooting for Amana 24 in. ADB1500AW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

Replaced control board 447325 in bosch SHU66C05UC/23; FD860300407. What code to select 0,1,2,3,4?


... Dishwashers

EDW5505EPS Electrolux Dishwasher. One cycle light stays on, but the other lights will not turn on when buttons are depressed. Unit will not turn on at all. I assume the control board is bad? How difficult is it to replace the control panel? Just remove the screws holding the stainless panel on? I assume the panel simply plugs in.


Hello,\015\012Have you tried holding the cancel button down for about 15 seconds as these units can sometimes get stuck in a cycle. Try this anyway first.\015\012\015\012Hope I helped. ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

I have a Whirlpool DU1055XTSS dishwasher that completely stopped working. I took it apart, found the thermal fuse to be bad, ordered a new, then replaced it and it worked for 2 loads. Now the thermal is open again. What could be "taking it out"? Is the thermal fuse strictly a thermal or does it repsond to current? It's 2 years old, i have already replaced the heating element, the main control board, and now the thermal....twice.


Hi.If the thermal fuse is blowing, that means that there is overheating.Common causes for overheating are:Thermostat cutting off too late.Plugged element.Plugged element means that the element sta ... Whirlpool Dishwashers

Hi silverdragon, re the dishlex 302 not heating or drying Have replaced heating element but unfortunately still cold. If the control panel has not shorted which it hadn't before, do you have any suggestions. My hubby would rather wait before buying a new dishwasher, but I don't want to throw good money after bad. Is there anyone you can suggest who would be able to check out the circuit board to see if i have missed anything.


Hi\015\012\015\012Check the two thermostats located at the inside bottom front\015\012panel of the dishwasher, if any one of them goes bad it won't heat. Hope this\015\012helps...please post back for further assistance.\015\012\015\ ... Dishwashers

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

Soap dispenser will not open. I replaced the wax motor and still nothing. Is there a way to verify if the control board is bad?


Verify that the bottom tray is not in backwards. There is a space on one side only, usually, and this keeps the door forced shut. ... Whirlpool Dishwashers

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

KitchenAid KUDP02FRSS1 lights flashing - Replacing control board


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

We have an AM-14 dishwasher. It now will not work on auto. It would sometimes and then not and now only on manual. We have had a couple people in to look at it. One says the main board was bad, so it was replaced and the problem continues. The board that was removed was put into another washer and it worked ok. We were told then that that a wire from the motor was wrong and thats when we called in another person. That person said the board was bad and they couldn't work on it. We are in Lancaste


... Hobart AM14-253 Free-standing Dishwasher

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

Control board gasket/cover won't attach to replacement console board


... Frigidaire PLD4555RFC Dishwasher

Bad control board


Hi again,\015\012\015\012Please reread my last posting. I answered these questions giving you all the instruction possible given the limitations of this type of comunication. If you are unsure, you might want to check the Repair Directo ... Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0713 seconds