Having problems with your Amana 24 in. ADB2500AW Built-in Dishwasher ?

Cycle light comes on but start button does not start (or light)


Answers :

Hi
\015\012\015\012

When the start button won't start then the issue is with\015\012either the control or the door latch which is located inside the control area.\015\012You'll have to take it apart and then check these two parts and the part that\015\012is bad should be replaced. Most probably it is the electronic control that is\015\012bad however, if these two parts are fine then check the motor. Hope this\015\012helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Amana 24 in. ADB2500AW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My dishwasher won't start when push the button , you can't put it in normal cycle and the a very faint light comes on the start but it won't start, lights stay on cycle and then go off. Any suggestions


... Maytag Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

My Jenn Air dishwasher won't start. The cycle lights come on, but the start button will not work. Also, some of the cycle's won't light up. I can only choose some of them, like I can't choose heavy wash or rinse only.


... Jenn-Air Dishwashers

I have a Tecnik TKD795/3 built in dishwasher. It is now making a gurgling noise as though it is draining water when I try to start the cycle, but the cycle does not start and no lights come on at all. I have tried pressing the outside two buttons to reset, but absolutely nothing happens and the gurgling noise continues until I release the power button. Can you help please?


... Tecnik 24 in. TKD795/3 Built-in Dishwasher

After selecting wash cycle,I push start button. washing light comes on for a second then goes off.start light keeps on blinking. washing cycle would not start.


Check flood switch float is on(the float under the bottom rack)...also the switch under that...also you ca use a 110 volt test cord to test the inlet valve ... Dishwashers

Kenmore Elite Dishwasher Model # 665.15914 Selected wash cycle...lights come on...pressed start...nothing happens...after about 10 seconds wash cycle lights go off... Is start button broken? What to do?


... Kenmore 15914 Built-in Dishwasher

Control Panel is stuck in Pots and Pans. Sometimes I have to hit the start button several times for it to work. When it does start washing the lights that come on are non sensical to the cycle. The drying light comes on immediately but I know it is washing.


It would be helpful to have the make and the full model number of the dishwasher.\015\012\015\012Looks like a problem with the keypad. Moisture etc. Might be as simple as opening up and running a hair dryer or could invovle a replacement. ... Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

We have a Maytag MDBH950AWS Dishwasher that won't start. When you press the start button the cycle light, washing light , heated dry, sanitize and extra rinse lights all come on the dishwasher fills with water and after a couple of minutes it shuts off. Any ideas what is wrong? Thanks


I have Miele incognito that when I shut the door it does not turn on? Not sure why it stopped working all the sudden ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Cycle light comes on but start button does not start (or light)


Hi\015\012\015\012When the start button won't start then the issue is with\015\012either the control or the door latch which is located inside the control area.\015\012You'll have to take it apart and then check these two parts and the pa ... Amana 24 in. ADB2500AW Built-in Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1581 seconds