Having problems with your Amana Dishwashers ?

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


Answers :

I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 degrees.
The person or persons that crimped on your spade push on) terminal ends, either cut thru most of the wire when stripping it for the terminal connector, leaving only very few wires, and /c they cannot carry the current, they simply vaporize leaving a terminal securely attached to plastic insulation - but no wire to carry the current.or he/she/it failed to properly prepare the wire end to expose enough wire, and crimped onto the insulation, leaving the wire hanging.
\015\012Pull the plug
\015\012Grab each of the power-related wire ends in turn and with your fingers, try to pull the crimped-on end off. Do not pull hard, although IF it was correctly stripped and crimped at the factory, you would not be able to. I am sure you will find one that feels very limp.. thats the culprit. Nip over to Home Depot or ACE and buy a Wire Termination kit ($10-20.00) which will contain all sizes andtypes you may need + a Cut/Strip and crimp tool.
\015\012
\015\012It was either a MON or FRI job. Too hungover from the weekend... or too jumpy to go home.
Repair Help & Product Troubleshooting for Amana Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

The door would not shut. We checked all around and nothing was blocking the door from shutting. We determined the latch on the door was not releasing. I forced the door shut. The touchpad works...lights come on but unit will not operate. The release handle on the front just wiggles back and forth without effect. Lowes says it is one of three parts...none returnable. Any thoughts on what part and whether this is something average consumer can self fix? Thanks.


Hi,\015\012 Lowes is right regarding the parts needed.\015\012\015\012First check the strike part is ok - that's on the body of the machine not the door.\015\012\015\012Unplug the machine.\015\012\015\012Remo ... Whirlpool DU1055XTS Built-in Dishwasher

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

My bosch dishwasher, one month old, has the active light flashing and the reset button won't reset it when I push it. A friend that was over opened the door when it was running because she can with hers, but ever since then, I had to take the water out and the active light is flashing and the wash light is lite. I hold the reset button for 5 seconds and then I shut it off for about 5 minutes, but when I turn it back on, the same things are happening


It sounds like the float is stuck. There is a float that stops the water from coming out when you open the door. It sounds like your friend stoped it in mid cycle and it jammed in the open position. Look on the inside of the machine for a plastic pie ... Bosch Dishwashers

Close door, no lights come on, no sign of power. Circuit breaker fine. Door latches fine. ran fine day before.


There is a fuse on your main control board that comes off and can be replaced somewhat easily. Start by TURNING OFF THE POWER. Open the door down to the floor and take a torx(or starhead) screwdriver and remove every screw (10 of them usually) along ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

No power to dishwasher and checked power breaker already it seams to be ok. I think its the door switch. I closed the door to hard one day so I wonder if it did something to it.


\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012\015\012Is there power getting to the dishwasher? This ca ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Dishwasher takes about 24-36 hours....yes hours....to complete the cycle because it stops....for sometimes more than an hour and then starts again on its own. When it stops the green light blinks. No explanation in the manual for a blinking green light. It will eventually complete the cycle, but who has two days to do a load of dishes?


... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

The karcher pressure washer was working one day then just stopped working the next day .Thepower light comes on when i press the on switch but nothing happens .So the power is getting to it but will just not fire up .Please could you advise


... Karcher Pressure Washers

Maytag MDBtt60awb will not start. Power definitely at dishwasher as panel lights are on, however "start" button does nothing. Dishwasher is less than 2 years old. The panel buttons eventually turn off. I've cycled the power to the unit with no response. The door is definitely latched. Unit ran fine a few days ago.


Most likely you have a bad motor when replacing the motor ihave found it is cheaper to get the pump with the motor attached where as they charge you more money for just the motor or the pump seprately try allbrands appliance parts they seem to be che ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

GE Profile Dishwasher, GSD4920 won't stop running. Still spraying water. No lights on the display. Looks like it ran all day since I started it before work. I turned power off and back on, but it still starts running when I close the door. Water is in the bottom and looks pretty dirty. Any ideas? Thanks, Larry


... GE GSD3800G - Multiple Color Built-in Dishwasher

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers

MY MAYTAG dishWASHER suddenly will not go through both cycles so the dishes do not get clean It is an older one that has the cutting board top. Not built in. Anyone out there. I thought if I take the door off I can look at the cycle switch. the model number is LWC300 and Series 01 Thanks a bunch


Dishwashers normally stop(thermostop)to wait for water to heat thus maybe the element is fault,try getting a good ohm reading from element,like 20 ohms,hope this helps ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

Hi, I have a Tecnik TKD/795 dishwasher (not sure which version - its the one with the three black rubber buttons on top). The problem is that the 'ready' button's led light is continuously on green 'on' so I can't change the program select. Also when I close the door to automatically start the cycle - nothing happens ! Please can you help ? Thanks Mr. Arwel Jones


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. This issue can be either due to a\015\012faulty door latch or door lock switch which is not engaging itself. An ... Tecnik 24 in. TKD795/3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1655 seconds