Having problems with your Annovi Reverberi AR RMW2.2G24 Pressure Washer Pump ?

Engine runs, but when I press pressure washer gun the engine stops

\015 I had run the engine with longer tern storage, but did not think that I had to add any storage fluid to the pump. the Honda engine runs fine, but when I Press the Pressure washer gun the engine stops instantly.\015

Answers :

Repair Help & Product Troubleshooting for Annovi Reverberi AR RMW2.2G24 Pressure Washer Pump

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Engine runs, but when I press pressure washer gun the engine stops


... Annovi Reverberi AR RMW2.2G24 Pressure Washer Pump

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

Hello, I own a Honda Pressure Washer (Porter Cable Model) with a Cat pump 2600psi and 6.5 hp. An Excellent machine for the past 7 years. Last fall I noticed it was not producing the full pressure but still Engine was running strong. This past weekend. started it up and used it for about 1 hour still with minimal pressure at full throttle. Then pressure was totally cut off. I stopped and started the engine the engine and it had minimal pressure again. Same thing happened again. I stopped the engi


... Honda Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

I have a Honda Excel Pressure washer with 5 hp engine. I just started using it for 5 - 10 minutes and the engine stopped running. I can't pull the cord to turn over the engine. Ithas plenty of oil, I disconnected the hose and the wand and still can't get the engine to turn over.What next?????


... Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

Hello there.My Karcher pressure washer motor constantly runs with no pressure coming out of trigger gun.I have tried another gun with the same result.The motor should stop/start when you press gun.The model is a 350M plus VPS. Could you please help.thanks


The valve that admits more water to be compressed is stuck. It is likely the O-Rings on it need replacing. No water to the pump, no pressure!\015\012\015\012The motor will stop when pressure is up to the designed pressure. ... Karcher Pressure Washers

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

I have a Generac 2300 pressure washer that has not been used for a couple of years. The engine runs fine but I get absolutely not increase in pressure when I press the trigger on the sprayer. Where should I start trying to diagnose? Thanks, Mike


... Pressure Washers

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers

Engine runs,no water when trigger pressed. - Karcher G2650HHR Gas Pressure Washer


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuck ... Karcher G2650HHR Gas Pressure Washer

Engine Stops after 10min run time - Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer


Check the breather hole on the gas cap.\015\012run the engine with the cap off and see if it still stalls. ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

I have a Durabuilt Pressure Washer Model DB 1404 1400PSI 1.6 GPM When I start it up it will run good, however if I stop pressing on the trigger it will not start up again. Would appreciate any help or suggestions. Is it possible to return it for factory service ???? Joe sanders,


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Unit Runs fine, except when you press the spay gun the engine stalls out. Unit was working fine, ran out of gas, filled tank and started engine. Engine was running fine, triggered spray gun and the engine stalls out.


... Pressure Washers

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

Pressure Washer stops running.


... Pressure Washers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

I have a XR2600 honda pressure washer that the engine dies when you stop spraying


... Pressure Washers

I have a XR2600 honda pressure washer that the engine dies when you stop spraying


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1475 seconds