Having problems with your Asko 1375 Dishwasher ?

The dishwasher is receiving water but it just seems to be dripping out, no pressure. No problems with drainage. DW95-2 Dishwasher code on side


Answers :

This is being caused by the vent tube design. The lower fitting is pushed up into the upper fitting so water leaks out from the top. The fittings are designed backwards. Remove front door panel and their will be a white tube running down the side. That tube is pushed up into its mate. Pull it down and silicone chalk all around the out side of that pieces and the inside of the upper piece. put them back together and then tape it with some duck tape. DO NOT USE FOR AT LEAST 24 hrs. let it get dried completely.then check out.\015\012------------\015\012also clean the gasket internally if there is a water build up in that area it drips out.\015\012-------------\015\012some other possibilities for more help as follows :-=-\015\012Here are some tips that will likely help you resolve this problem:\015\012
    \015\012
  • Check the spray arms in the dishwasher for cracks or splits. Check the holes in the spray arms to make sure that they are clear. These types of problems with the spray arms could cause a wave action inside the dishwasher tub that could cause a leak.
  • \015\012
  • Make sure that the dishwasher is properly leveled from front to back.
  • \015\012
  • Check the tub seal at the bottom of each side of the dishwasher for damage. Make sure it is properly positioned as shown in the image below.
  • \015\012
  • If the above tips don't help, I recommend that you order and install the side splash shields (part 154701001) as shown in the image below.
  • \015\012
  • If you still have problems, you may need to replace the bottom door seal wiper (part 154588201). Here are the steps to replace this part:\015\012
      \015\012
    • Remove lower rack from tub
    • \015\012
    • Open the door completely down so the door seal can be pulled out from the right side
    • \015\012
    • Pull it straight into the tub to remove it
    • \015\012
    • When installing the new seal place it in the channel just enough to hold in place
    • \015\012
    • Close the door so the tub will push the seal into place.
    \015\012------------\015\012This will help. Thanks please keep updated.please do rate the solution\015\012if helped.thank you for using fixya.
Repair Help & Product Troubleshooting for Asko 1375 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The dishwasher is receiving water but it just seems to be dripping out, no pressure. No problems with drainage. DW95-2 Dishwasher code on side


This is being caused by the vent tube design. The lower fitting is pushed up into the upper fitting so water leaks out from the top. The fittings are designed backwards. Remove front door panel and their will be a white tube running down the si ... Asko 1375 Dishwasher

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I received the IE error code (Water inlet trouble) on my LG dishwasher. I've checked the hose and the water flow into the machine and there is no problem there. Where else can I check?


... LG LDF6810 Built-in Dishwasher

Lg dishwasher model LD-2163SH problem code IE meaning water is not supplied. I have checked that the valve is open and water line has sufficient pressure. Inlet hose is also not kinked and pump for drain is functioning normal. Pl suggest solution urgently? manoj


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

John Lewis dishwasher jldww1203 error code 30 tipping rocking works very temporarily as in just a few mins maybe 1 cycle, had side off there a pipe that just hangs fromtge bottom of side water thing it drips small amount less than teaspoon in entire cycle


... Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Water will flow out of your inlet pressure. The pump takes from your machine to spray. The same water is circulated during wash!Hence try the method I have informed you. If it is a micro controller problem you have to contact the service ... Dishwashers

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Took these from a previous page, because this is what is happening to our lab Miele Platinum G892/G892 SC. Can you tell me what the problem is and how to fix it? Thanks. intake /drain light is flashing,full water- Guest Feb 26, 2009- I have same problem - open the door and there is water at the bottom of the dishwasher - when I restart program, the water drains out fine. Also, I have great water pressure coming into the dishwasher, filters are clean, etc. I am suspecting it is a circula


If there is verified power at the pump motor - your timer is defective.Thanks For using Fixya!! ... Dishwashers

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

The upper rack side rail is loose where it attaches to the side wall of the dishwasher. It allows the upper rack to wobble. When the dishwasher is turned on, the force of the water pushes the rack forward so it detaches from the water supply and the arm does not rotate. The arm and connection are all clear and the arm is able to rotate, so those problems are not a factor. The wheels are in good condition. The left rail is a little loose; the right one is very loose. There must be a way t


Hello melinda.... Here is a link to searspartsdirect.com ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v


... Asko D1876 Dishwasher

Diswasher TYP NBKH, SERVICE 8546 892 10010 Problem: For all programs except rinse and charge 1/2 for all programs. Pre-rinse and rinse for 50 Bio, 60 and 70 OK. Downloading water to wash causes multiple knocking (on the left side dishwashers) and simultaneous blinking light (relais?). Opening doors and adding water (different amounts - from 0.5 to 2 l) brings the normal work of dishwasher back. Rinse with cold water after washing OK. Final cleaning with hot water causes knocking again. After r


... Dishwashers

Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?


There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

I have a model du1145XTPQ dishwasher. I doesn't seem to fill with enough water so I have to add with every cycle. The repairman says that there is no filter and my water pressure wasn't high enough. The water company was out and said water pressure was at 75pounds and that was not my problem. Is there a filter somewhere that might be cloged? thanks


The dishwasher has a float switch which detects if the dishwasher is filled. If the travel of the float is not sufficient it may be triggering early and causing the inlet valve to shut. Also see page 21 in the ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have a EuroTech dishwasher Model# EDW254E/SB. It was working fine but now it gives the Err code:er1 Its not letting incoming water in i know that. As well I have been told to try reducing the water pressure at the facet. Did that nothing.It drains but wont cycle to the next stage and let water in. I am presuming there is a valve of some sort not opening? And does the dishwasher have to be completly romoved to fix. Thanks


Hi and welcome to FixYa. I am Kelly. \015\012\015\012This is a water level sensing problem. Look inside your lower wash tub area and see if you either see a circular device off to one side or a finger like device sticking up about 2 inc ... Dishwashers

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

I have an LG dishwasher that keeps giving an 1E error code. The code means water inlet trouble and recommends the following. Check clogging of water inlet hose(or hose twist or freezing) Check if it's suspension of water supply The problem doesn't seem to be either. ?


Try replacing the water inlet solenoid valve (it may have an open coil). The water line goes directly to it. ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2850 seconds