Having problems with your Asko 1385 Dishwasher ?

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


Answers :

CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT.
Hi Richard, it seems like I have the same problem as you did. How do you go about fixing this? Can it be done on your own, or do you have to call someone in? Thanks
Repair Help & Product Troubleshooting for Asko 1385 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

My d1716 continues to run, but does not move forward in the cycle. I can even open the door and it continues running. If I didn't unplug it, the motor would likely burn out. Do I need a new dial? Thanks.


Hi\015\012\015\012I would suggest that your flood switch has been activated. There is a float on the bottom plate or base plate of the machine. If there is a water leak, the float rises and triggers the flood switch.\015\012\0 ... Asko D1716 Built-in Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Bosch SHX99A15UC Apexx dishwasher won't drain and continues to cycle (you can hear the motor running, but no water) even with the door open. I've flipped the breaker a number of times and the water eventually drained, over night, but it won't run normally now. Any help of suggestions are greatly appreciated.


... Bosch 24 in. SHX99A15UC Stainless Steel Dishwasher

Continual draining continues to drain with motor running even when door is open therefore will not go onto another cycle reset makes no difference


Has the unit pumped out all the water? It may have a blocked waste hose. ... Dishwashers

Dishwasher will fill and goes thru wash cycle fine, But even though the timer will continue to rotate,motor will not run or hum in drain cycle.


Http://www.repairclinic.com/Dishwasher-Troubleshooting\015\012\015\012 ... GE Dishwashers

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

I've got a GE model GLD4408R00WW front load dishwasher, which was not filling, even though you could hear the motor running. Tried resetting it by turning off the power at the wall switch, and then from the breaker itself, but now, see the "Normal" wash cycle and Heated dry lights blinking when power is returned...


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... GE Dishwashers

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

My dishwasher motor will not stop running, even after disconnecting the power and plugging back in. It does not run through a cycle with any water, but the motor runs even when the door is open.


... Viking DFUD04 Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

The motor continues to run with the diswasher powered off. In addition it will no longer enter wash mode. It can be powered on and wash mode can be selected, but nothing happens except the motor continues to run. Cycling the power feed off and back on does not solve the problem.


Hello John,\015\012\015\012The simple answer (without looking at the wiring diagram) is the float switch. The simple answer (after looking at the wiring diagram) is the float switch. I've posted the wiring diagram for this washer to Flick ... LG 24 in. LDS 5811 Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

My Kenmore built-in dishwasher is running its cycles normally, but no water is coming into the machine so it runs the cycles dry (even a rinse cycle). Can you advise? If a part is needed, is it an expensive one? Thank you!!


Sound like the inlet water valve is to blame here - or else the main controller board relay is not telling it to open. Further testing will be necessary to determine which is the cause.If it is the board - you are better off getting a new ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Made funny noise; stopped to investigate; then wouldn't restart; followed directions below from FixYa and restarted. It finished the cycle, apparently correctly, except it left a little water in the tub. Also, continued to make a lot of noise--a loud motor hum/buzz or similar. Did not make this noise during dry cycle. Dishwasher is Kenmore Model 665; stock number 16839. Can you give continued diagnostic instructions? Appears there is a cracked washer under the lower wand assembly; th


The solution was nearly correct. The person who answered only forgot to mention that water level and pressure switch must be tested. This can cause drain pump working longer than necessary and humming, and machine underfilling, which can cause noise ... Dishwashers

Bosch SHX46B05UC Dishwasher -- Motor continues to run (up to a few hours) after running and completing "Regular Wash" cycle. No water was left inside and "Clean" indicator was lit but motor was humming away...


... Bosch Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1738 seconds