Having problems with your Asko 1385 Dishwasher ?

Display reads f2 - Asko 1385 Dishwasher


Answers :

Hello,

Welcome to FixYa.

Based on your description It is likely nothing very serious.

The "F2" with Asko dishwashers means the control is indicating an overfill has been detected.
Whether the unit has actually overfilled or not remains to be seen, but to reset it is fairly simple...if nothing else is at fault.

**before proceeding turn the dishwasher power off via the home breaker panel, or unplug it from the wall if that is possible...most are hard wired to the home electrical...safety first**

The first thing to do is remove the toe panel/kick plate and inspect the base for water. If water is present, with the aid of a sponge, towels, or a wet-dry shop vacuum, absorb the water from the base.

By way of removing the water from the overfill basin should "reset" the unit. If the unit works fine after resetting the power/breaker it can likely be chalked up to a drain back-up or obstruction in the drain hose or pump.

Try this and let me know what you find and I`ll assist you in moving forward if necessary.

Thanks for choosing FixYa and good luck.

Regards,

Macmarkus :)
Repair Help & Product Troubleshooting for Asko 1385 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Display reads f2 - Asko 1385 Dishwasher


Hello,Welcome to FixYa.Based on your description It is likely nothing very serious.The "F2" with Asko dishwash ... Asko 1385 Dishwasher

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Zanussi dishwasher when cycle finished displays .60 instead of 0?


... Dishwashers

Asko displays F2 - Asko D1796FI Built-in Dishwasher


... Asko D1796FI Built-in Dishwasher

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

Asko d5131 asko dishwasher displaying f4 several seconds after being turned on


... Dishwashers

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan


Hello,Welcome to FixYa. \015\012\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions ... Dishwashers

My Hotpoint aquarius FDW75 dishwasher will not fill with water and when turned on the display reads H2O and then displays the code AO6


... Dishwashers

Dw010 dishwasher displays code e3 - Asko 1595 Dishwasher


... Asko 1595 Dishwasher

My sink got clogged and now my bosch dishwasher SHU43C05UC wont fill with water. I read on line that it most likely is the float is stuck and to access the front kickplate needs to be removed. Is there a diagnostic test that I can do that will display on the LED to make sure that this is the problem. How involved is it to unstick the float. Can it be done without moving the dishwasher and just working from the kickplate area?


It is most likely that you need to do the following\015\012\015\012Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of th ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

ASKO D3350 Dishwasher Displaying F4 Code


... Asko 24 in. D3350 Dishwasher

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

Bosch Dishwasher SGS43E02 Exxcel. Switches on at main switch (0 appears in the numerical display) but none of the right hand programme buttons seem to be working! Have checked filter on water supply hose and that doesn't look blocked.


Obviously a faulty connection. Lots of switching off and on and holding down the buttons eventually sorted it! ... Bosch 24 in. SGS43E02 Exxcel Built-In Dishwasher

Have Hobart CL-44E dishwasher that won't stop the 'fill' cycle. Both upper and lower float/probe sensors test as operating, Solonoid valves both functional; Display reads 'tank filling', and will not go into 'wash' cycle...what to do??


... Hobart Dishwashers

My Bosch dishwasher is making a loud noise and the displays is reading 2H?


... Bosch SHU5315UC Dishwasher

I need a new front panel and door seal for a customers dishwasher. It is a fisher and paykel Nautilas The opperating instructions say it is a model 920 . I can not read the model No from inside door as it has been cleaned off the sticker. The panel is black and has the led display on the right hand side


Check out www.applianceart.com ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

ASKO 1905 Dishwasher. F2 fault appears on the display screen.I have checked the pump as per instructions in the owners manual but the pump impeller was moving freely. The drain hose isn't blocked or kinked either. Can someone please help. Thanx.


F2 error usually is water in bottom pane. A floter is rising and cutting supply and displayin g F2\015\012\015\012\015\012\015\012 This us usually due to somthing leaking. Ie the light in machine, gasket is broken and water leaks intu bottom pane.\01 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1898 seconds