Having problems with your Asko 1385 Dishwasher ?

Dishwasher pumps dry, adds and heats water, but does not go through wash cycle. It apparently continues through all cycles, but never pumps the water through the spray arms in either wash or rinse cycles. spray arms are both free and clean, no debris anywhere obvious.


Answers :

Hi.

The impeller pump is probably faulty.

Before going for the pump check the drain well and drain hose, drain blockage may prevent the machine from switching to recirculate. Also double check there is no blockage or leak in lines to spray arms and that the orifices are not clogged.
Testing on the impeller is done energizing the pump to check if it switches to recirculate and accessing pump hose checking for blockage.

Other parts that must be tested are the door switch, that can interrupt the cycle, and the thermostat, that is used to determine when to start the impeller pump.

If pump and all the part mentioned above are OK, then the problem is a defective control module.
Repair Help & Product Troubleshooting for Asko 1385 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher pumps dry, adds and heats water, but does not go through wash cycle. It apparently continues through all cycles, but never pumps the water through the spray arms in either wash or rinse cycles. spray arms are both free and clean, no debris anywhere obvious.


Hi.The impeller pump is probably faulty. Before going for the pump check the drain well and drain hose, drain blockage may prevent the machine from switching to recirculate. Also double check there is no blockage or leak in li ... Asko 1385 Dishwasher

Bosch Logixx dishwasher gets stuck on either wash or final rinse programme and runs all night until stopped manually. heat, pump, water supply, arms led controls all working. Any ideas as to the fault


You have a bad control module. send me a 4 thumbs post if this was helpful to you.p.s im a old bosch tech ... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

Machine starts fills Ok but when it clicks on to start the wash pump, nothing happens, I can hear a faint hum. When cancelling wash and starting new wash it pumps out ok too. After rinse cycle it indicates a completed wash, but no water has been pumped through washer arms.


Sounds like your main circulation pump is not working, if it is humming when it is supposed to start, sounds like it is getiing power, so probably not the control circuits, can you measure voltage to pump?if you are getting 120 there, probably pu ... Asko D1876 Dishwasher

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I set rotary dial for Normal Wash which it does but does not turn off, rotary dial keeps turning automatically thru t Water Miser, Rinse Hold, Drying, Plate Warmer until reaches Off. Dishwasher operates normally otherwise. Have cleaned the pump and spray arm.


Hello, welcome to FixYa.I will start by saying your po ... Kenmore 17259 Free-standing Dishwasher

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found o ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Model MDB 7600AWQ It is not cleaning dishes well and the bottom water 'slinger' is not rotating. We disassemble the lower assembly and cleaned extensive soap scum and hard water deposits. Lower slinger is still not rotating. Water temp and water level are fine. Pump is getting water to upper slinger and pumping water to drain between wash and rinse and after rinse.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Water pump evacuates water but does not pump in the wash or rinse


... Kelvinator MDB121RF Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

I have mod. # FDB1050REB0 the top rack wash/rise arm is not turning at anytime during the wash cycle--- We are not covering the hole into which the water is being pumped---- the bottom washing is turning---- this leads me to to believe the line to the top arm is obstructed from the pump to the wash outlet (in the top of the machine)---- what can I do to check the line?


Hi\015\012\015\012Please check if something is blocked near the top spray arm\015\012and also make sure that all holes are open. Use a sharp metal pin to clean the\015\012holes on the top spray arm. Make sure the water pressure is not low ... Frigidaire Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Hi I have a Blanco dishwasher BFDw8 which is having poor wash results in the top tray I have tried all the trouble shooting things in manual. Investigated further by opening door during wash cycle several times and discovered the top arm is not moving although water is still coming out of the arms. I did get a split pea particle out of the arm approx 2mm and have since had a mildly better wash and have used superior wash powder and rinse aid to try and help. Also have put a cleaner through di


\015\012\015\012Check the water temperature. Should be 125 to 140 F. \015\012\015\012Check pump re-circulation., Listen, see if it sounds like it is spraying the water around with enough pressure. ... Dishwashers

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

Water flow in and pumping out, but not wash dishes, SPRAY ARM BLOCKED, pump not rotating and getting hot


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

My fisher & paykel dishwasher won't empty water after washing and rinsing. Water overflowed from the dishwasher then remained in the bottom. I can hear the pumpt trying to pump. The dishwasher


... Fisher and Paykel 24 in. DS603H SS Free-standing Dishwasher

Wash arms wont spin .it fills with water and goes thru normal cycle and will pump the water out but no water gets to the washer arms.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1814 seconds