Having problems with your Asko 1385 Dishwasher ?

Dishwasher runs fine but trips circuit breaker at end of cycle


Answers :

Your heating element might be shorted. Try turning off heated dry and see what happens.
Repair Help & Product Troubleshooting for Asko 1385 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher runs fine but trips circuit breaker at end of cycle


Your heating element might be shorted. Try turning off heated dry and see what happens. ... Asko 1385 Dishwasher

I received a second-hand as-is Akso D3530 (model #107353001) dishwasher. It washes perfectly fine, but at the end of the cycle, it keeps running. It does not seem to be the drain that is running, but rather the circulating pump. I have fully emptied the pan of water (there was only a little in it (you couldn't see it until you removed the sieve) using a turkey baster and it keeps running. I also checked the float sensor in the bottom. The float sensor is not tripped, and when I manually trip it,


Hi.The float switch is not a water level switch, but an overfill switch. The control board uses the input from the pressure sensor to decide when to stop the pump.When you open the float switch circuit the machine 'thinks' that ther ... Asko 24 in. D3530FI Built-in Dishwasher

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

Model KUDM24SEWH1 dishwasher stopped running. Had to remove dishes and clear water from bottom. No response from operation buttons. Circuit breaker not tripped. Other outlets on same circuit work fine.


... KitchenAid Dishwashers

I have a Whirlpool dishwasher, model DU943 that's under 7 years old. I went to use it last night and it won't power on. I tried selecting all of the cycles, but the dishwasher never came on. I looked through the troubleshooting tips in my manual (like checking the circuit breaker for a tripped fuse, which was fine) and I still have a problem. what else can I try? thanks.


Hello- This unit has a thermal fuse inside the door panel on the control. This part is replaceable. If it is bad, replace.- and would suggest not using heated dry as this is most common cause of fuse failure. Let me know if this info helps- have more ... Whirlpool Dishwashers

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

My Danby DDW1899 W was installed and ran through 3-4 loads fine, then at the end of one washing the power just went off. The circuit may have been under a load when this happened but the circuit breaker did not trip. Could this be a dishwasher fuse? If so, where is it and how to replace?


... Danby DDW1809W Builtin Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Hi kalybon,\015\012\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Mid-cycle Dishwasher not working following a circuit breaker trip


... Dishwashers

I have a Bosch SGI4005 AU/07. When it completes the end of the cycle it trips the houes electrical circuit breaker. It continues to trip the circuit breaker for an additional 5 minutes then all is well. It will do the entire wash. Is this a common problem and has someone got a wiring circuit diagram for this unit.? Any assitance is appreciated.


... Bosch Dishwashers

Dishlex global 200 dishwasher is tripping the circuit breaker


... Dishwashers

My Samsung dishwasher (DMR57LFS) trips the circuit breaker after it completes any cycle. Somtimes not in use you hear a pop and the circuit breaker will trip. Any ideas


... Samsung DMR77LHS Tall Tub Dishwasher

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

Circuit breaker trips when dishwasher is off.


... Hotpoint 23 in. BF50 Built-in Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

Shu6802uc Bosch Dishwasher trips house circuit near the end of the wash cycle. Any Ideas? Can flip the circuit but it most often trips again.


Poss heater leaking to earth. ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

At the end of the scrubber cycle, I get an F2 code and have to trip the breaker off and on to get it re-started. It then runs normal to the end of the washing cycles.


F2 \015\012means that the rotor (PN 525884P) is sensed to not be turning, It could \015\012be a small piece of food debris, a tiny fragment of a shell or broken \015\012glass, has gotten lodged in the wash impeller, or it could be a seized \01 ... Asko Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2488 seconds