Having problems with your Asko 24 in. 1805 Built-in Dishwasher ?

We currently replaced our water heater, after we replaced it all our water is running fine hot and cold, and i went to turn on my dishwater and no water is running, we checked the valves and everything is opened but when i opened it up it was heated up and no water was going through can you help!


Answers :

Hi,

Reach inside your d/w and jiggle the mushroom shaped float switch\015\012located on floor of d/w. should move freely up and down if its stuck\015\012up(or something lodged under it your unit wont fill with water)....

Check and let me know if that would fix the issue.

Thanks for using Fixya.

Do rate the solution as 'Fixya' if 100% satisfied.
Repair Help & Product Troubleshooting for Asko 24 in. 1805 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We currently replaced our water heater, after we replaced it all our water is running fine hot and cold, and i went to turn on my dishwater and no water is running, we checked the valves and everything is opened but when i opened it up it was heated up and no water was going through can you help!


Hi,Reach inside your d/w and jiggle the mushroom shaped float switch\015\012located on floor of d/w. should move freely up and down if its stuck\015\012up(or something lodged under it your unit wont fill with water)....Check a ... Asko 24 in. 1805 Built-in Dishwasher

I have a Miele G868 dishwasher. It is 15 yrs old. 8 months ago the soap dispenser wouldn't close, so I got another dispenser from Miele and replaced it myself. Everything worked fine until 3 months later, when the soap dispenser did not open. After 3 restarts, it began to function as it should. Now 5 months later, the soap dispenser is not opening at all. Here are my observations: 1. Economy wash cycle should run 35 minutes but only runs 13 now. 2. Water in machine is not hot, even though I run


... Miele Dishwashers

I have a pot scrubber 600. I just replaced the water line. I had to disconnect the electric wire to service the unit. Everything is running except the water doesn't fill, and there is an awful buzz from the actuator for the water discharge. What is going on? The water valve is on but doesn't fill.


So tell...me...you replaced the water line why......its probably moot as to why you did it....just realize that the large majority of no water problems are due to a wire off or loose on a water solenoid valve or a bad solenoid....I am going to provid ... GE Dishwashers

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Hello, we have a Frigidaire dishwasher Model# FDB1250REC2. There was all kinds of junk down in the lower filter area and when I tried to remove the parts they all came out together and then fell apart. I need to see how the parts go back together, because I thought I had them in there correctly, but when I opened up the dishwasher after running it the water sprayer was laying on the heating element. Could you please help me get it back together right? Thank you


I am having the same problem...were you able to fix it? ... Frigidaire Dishwashers

I have a haier dishwasher model WQP12 AFM, I've replaced the wash pump motor and drain pump (they had been damaged with water after last repair person didn't put widget around drain hose which split and water accumulated on bottom). It well for about two weeks, then it would not go through it's cycle and I noted water not heating up. Have checked element with meter, thats fine, I replaced timersince it wasn't going through its cycle and that has not changed anything. Any suggustions?? Cheers


... Haier Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Waterintake stops after approx. 35 sec.waterlevel is to low,detergent compartement will not open because of low waterlevel and also water will not heat, because heating element is not covered with water. If I put water in by hand to get the waterlevel above heatingelement everything is fine. Dishwasher has been working without any problems till approx. 18 mths ago. Have also adjusted waterintake time as described in manual by taking off dial knob and adjusted with small flat skrewdriver, but not


The machine fills by time only as you have already determined. The intake screen on the water valve is probably plugged up and cleaning it should solve your problem. You will have to turn off the supply to the dishwasher and disconnect the water feed ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

BOSCH Dishwasher Problem I have a dishwasher (SHV46C13UC/33) that when I start any of the three cycles it continues to run until I open it and do the 'cancel' function. The 'rinse/drain' seems to be running fine, but there is a film left after that mode. I've checked the water inlet, which is open and fine. And, it does drain properly. Is there a SENSOR I need to clean periodically? Or, is the man control module the problem? What's going on?


I would check the float switch in the bottom should be a mushroom shaped thing that turns the pump off after the water level in the machine has dropped to a certain level or has totally emptied. ... Bosch 24 in. SHV46C13UC Free-Standing Dishwasher

My kitchenaid KUDI01DL dishwasher began making a lot of noise while running, then subsequently decided not to circulate the water around to wash the dishes. It sounds like the motor is running (maybe) but there is no washing action going on. The machine will fill, drain and heat the water but nothing else. Is it likely that the pump/motor assembly has ceased to function properly? thanks...


The problem is very likely in the chopper and/or somewhat possible in the impeller. The chopper is replaceable from the front. Disassemble the pump, the chopper will be on its left side under a cover. That cover is kinda tricky to remove (remove all ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1323 seconds