Having problems with your Asko 24 in. D3250 Built-in Dishwasher ?

Whenever the dishwasher is started the drain pump stay on. It will only stop when the breaker is switched off.


Answers :

Chances are you sump level monitor is stuck to the side of the drain with fat of other food substance that has got past the filter.
1 Empty your machine .
2. Remove the stainless steel filter below the lower basket.
3. Pour a kettle of boiling water down the hole beneath where the filter is.
4.Set the machine to rinse.
hopefully this will cure the problem
Repair Help & Product Troubleshooting for Asko 24 in. D3250 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whenever the dishwasher is started the drain pump stay on. It will only stop when the breaker is switched off.


Chances are you sump level monitor is stuck to the side of the drain with fat of other food substance that has got past the filter.1 Empty your machine . 2. Remove the stainless steel filter below the lower basket.3. Pour a kettle o ... Asko 24 in. D3250 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric


... Bosch SHU5315UC Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

We have a IKEA Whirlpool DWF 407 dishwasher that suddenly stopped pumping in water. It's just stuck in a loop where it sounds like the water pump is dryheaving and soon after it starts smelling a bit burnt and smells a bit like a battery. I've checked the overflooding breaker and there's no water down there and I can hear the switch turning on if I move the floater upwards. Also checked so that the water hose up on top of the machine is securely fixed. Any ideas?


... Whirlpool 24 in. ADG6340 Built-in Dishwasher

Have a Zanussi 6344 dishwasher, when starting the machine it starts pumping en then stops. When adding water the same problem, starts pumping to drain the water and then stops again ? It drains perfectly, seems the machine thinks there's still water inside, is there some sensor that checks the water level or so ?


... Kuppersbusch 24 in. IG6344 Built-In Dishwasher

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Drain pump continuously runs when dishwasher switched on no displays on front ,stays full does not heat ,or start program


Our AEG did this (but it did display an errorcode). It simply meant that there was a water on the bottom of the machine. I found this out by tilting the machine so the water leaked out and than the machine ran normally for the next two washes. Then t ... Dishwashers

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Hi, Zanussi dishwasher DE6344, when starting any program the machine start pumping (draining) for a while and then stops, lights start flashing saying that the draining is faulty. Checked the drainpipe and when adding some water the machine drains it perfectly, still the program won't start. Looks like it thinks there still water inside ? Suggestions ?


... Zanussi 24 in. DE6544 Built-in Dishwasher

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2553 seconds