Having problems with your Asko 24 in. D3530FI Built-in Dishwasher ?

I received a second-hand as-is Akso D3530 (model #107353001) dishwasher. It washes perfectly fine, but at the end of the cycle, it keeps running. It does not seem to be the drain that is running, but rather the circulating pump. I have fully emptied the pan of water (there was only a little in it (you couldn't see it until you removed the sieve) using a turkey baster and it keeps running. I also checked the float sensor in the bottom. The float sensor is not tripped, and when I manually trip it,


Answers :

Hi.

The float switch is not a water level switch, but an overfill switch. The control board uses the input from the pressure sensor to decide when to stop the pump.
When you open the float switch circuit the machine 'thinks' that there is overfill and starts the pump. Door must be closed and othe conditions met.

The pressure sensor is sometimes difficult to test and gets replaced straight away. The part is not expensive.

You mentioned that you left a little bit of water inside the tub. Perform again testing with no water. A little bit of water may be detected wrongly by a malfunctioning pressure sensor. Ensure power is not connected if not necessary and ensure that you did a power reset by disconnecting appliance for a couple of minutes. Clean thoroughly the drain well and remove water from inside the tub completely.

At the end of the cycle this machines also check dryness and temperature. Check also dryness (humidity)sensor and thermostat.

Regards.

Ginko.
Hi
\015\012
\015\012Use a multimeter and check the reading to the drain pump. Make sure that the drain pump connections are fine and the wiring to the control panel seems to be ok. Hope this helps... Please post back if you need more information.
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for Asko 24 in. D3530FI Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I received a second-hand as-is Akso D3530 (model #107353001) dishwasher. It washes perfectly fine, but at the end of the cycle, it keeps running. It does not seem to be the drain that is running, but rather the circulating pump. I have fully emptied the pan of water (there was only a little in it (you couldn't see it until you removed the sieve) using a turkey baster and it keeps running. I also checked the float sensor in the bottom. The float sensor is not tripped, and when I manually trip it,


Hi.The float switch is not a water level switch, but an overfill switch. The control board uses the input from the pressure sensor to decide when to stop the pump.When you open the float switch circuit the machine 'thinks' that ther ... Asko 24 in. D3530FI Built-in Dishwasher

E4 error light comes on, dishwasher won't run, this apparently means water is on a sensor, have removed water from collection tray in bottom, tilted machine backward to dry out sensor, left for 24 hours, machine still won't run. Currently a very small new counter top but a useless dishwasher.


The problem is related to the floater assembly inside the dishwasher. It is filling up with gunk and stop working properly. I found out the hard way after a good spill. The solution is easy but takes a bit of time.1. Unplug the power and water h ... Danby DDW497W 22 in. Countertop Dishwasher

Float does not shut off the water when dishwasher is being filled. IWater keeps running, fills up and runs out of the front of the dishwasher. Also it will not pump the water out at end of cycle.


Check the float to make sure it moves freely up and down, and it should click when it moves. Remove float and clean around the float tube-you may need to do this from below, through the access panel. Use white vinegar to scrub the float and ... Maytag MDC4650AW Built-in Dishwasher

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

In replacing the float that senses water level on a Hobart AM 14 dishwasher, I see that the whole assembly is free to rotate after the c-clip is reinstalled. Past experience is that sometimes this plastic float will be found upside-down, on top of the probe which houses the reed switch & thermistor temperature sensor. What's to keep the float from rotating like this? Nothing appears to be broken or missing on the assembly from what I can see. THANKS!!!.......Lee


... Hobart AM14-253 Free-standing Dishwasher

In replacing the float that senses water level, I see that the whole assembly is free to rotate after the c-clip is reinstalled. Past experience is that sometimes this plastic float will be found upside-down, on top of the probe which houses the reed switch & thermistor temperature sensor. What's to keep the float from rotating like this? Nothing appears to be broken or missing on the assembly from what I can see. THANKS!!!.......Lee


You may have installed the stainless float retainer backwards. The hook on the retainer that holds the float faces the tank wall and fits into a flat on the probe. This prevents the rotation and will better secure the float. ... Hobart 42 in. AM14C-154 Free-standing Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Asko 1755 dishwasher. The pump keeps running and the fault lights indicate high water level. Problem appears to have been a clogged filter, which is now remedied and all water removed. How do I reset the machine?


... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

I seem to have the same problem on my AEG diswasher where the pump keeps on running but brings no water in. After reading a few blogs, it seemed like the antiflood system was triggered. Moved it away from the wall to check and saw that a mouse ate my polystireen float while we were on holiday. How do I fix this?


Hi\015\012\015\012\015\012The polystyrene float you are referring is the water inlet valve where water hose is connected to. You would need to check & replace the water inlet valve. Hope this helps... Please post back if you ... AEG Favorit 50500 Built-in Dishwasher

Hi, I have an ASKO D3250 dishwasher and it keeps stopping during the wash cycle and flashing the heavy pots and pots symbol simultaneously. I tried cleaning the filter basket and found a little plastic part floating in there that has printed on it PP-T20. I don't know where this piece goes or if it's even the culprit. There is a little bit of water not draining from the filter area when I unscrew the outer filter basket, I cleaned it out, but when I re-run it, it still stops and gives the dual f


The part is a cap for the drain pump. You can put it back into position by removing the filters and placing it to the left of where the circular filter would be positioned. The part goes in with the part numbers on the bottom facing down. When posit ... Asko 24 in. D3530FI Built-in Dishwasher

Why does my Kenmore dishwasher keep running water? I've replaced the overflow switch and the float with the same results?


I'm gonna guess that you are manually turning the water on and off under the sink. if this is the case, you are taking the place of the water inlet valve which is probably bad or stuck open. since you have already gotten your feet wet with repairs ... Bosch 24 in. SHU5305UC Built-in Dishwasher

The dishwasher cycles down to 1min and then keeps trying to empty. It never does get there though. Water is still in the sump. Emptied this out once and it started ok again. Removed side cleaned out the sticky float switch. This was full of gunk. Noticed rear tank was partially blocked. Is this anything? Which is the outlet solenoid


... Neff 24 in. S5457X0GB Built-in Dishwasher

My frigidaire dishwasher will not shut off the water being pumped into the dishwasher. It just keeps pumping in even after the required fill time and will not shut off, eventually I have to turn off the shut off so that it doesn't overflow. The float is working ok. Is this a sensor,circuit board?


... Frigidaire Dishwashers

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

Electrolux Dishwasher 24 " not enough water new fill valve new float hot water Water lines clear. water too low float never rises amd the dishwasher runs water barly covers the top of the filter straner Model FDBB2455FS0


If i was at your home as a repairman this is what i would do.if your water pressure was good at the kitchen sink,i would turn water off to dishwasher undo water connection at the fill valve,and place water line in a bucket and turn on wa ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Smasungdishwasher DMT610RHS error codeCE showsup. eventhough the is not locked in, it still runs with error code CE, but the water is not coming in. but the motor is running. unless I plugged out, it keeps running. I shut off, but not responding power ONOFF.no response to any button on the control pannel. but keeps running.


... Samsung Dishwashers

Hi i have a asko dishwasher the water will not enter the washer and the drain pump keeps going i have clecked the filer in the inlet do you think it could be water in the base lifting the float stopping the water inlet if so how do you drail the water out from the float? the model is d1706 thanks brian


Check this solution ... Asko 24 in. D3250 Built-in Dishwasher

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle keeps running. I have checked the screens and they were clear. I have a Bosch Dishwasher SHU4302UC and I can't figure out how to cancel the cycle it's in. It keeps running and running. It pumped all the water out and the LED indicator are lit for the rinse/dry.


There is a recall on the control board of many of these models. I have written a guide to help. It is here. Look for the phone number near ... Bosch 24 in. SHU43 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1608 seconds