Having problems with your Asko D1706 Built-in Dishwasher ?

My ASKO D1706 drain pump will not stop running and the system will not advance to the next cycle even though the timer keeps spinning. What's happening here?


Answers :

Hello,

Welcome to FixYa.

Based on your description "drain pump will not stop running and the system will not advance to the next cycle even though the timer keeps spinning" , the good news...It is likely nothing very serious, but the "resolve" requires some investigation on your part.

The drain stuck cycle are directly related with overfill scenarios for Asko dishwashers of this era.
This is meaning the overfill switch is indicating an overfill has been detected. Whether the unit has actually overfilled or not remains to be seen.

In the event it has, the outlet/drain pump motor is automatically turned on via either the pressure switch or a float in the base if sensing an overfill and removing water from inside the dishwasher will do nothing to resolve this error, but you can...

**before proceeding turn the dishwasher power off via the home breaker panel, or unplug it from the wall if that is possible...most are hard wired to the home electrical...safety first**

The first thing to do is remove the toe panel/kick plate and inspect the base for water. If water is present, with the aid of a sponge, towels, or a wet-dry shop vacuum, absorb the water from the base...it should be known that if you leave the unit for a few days, the water in the base will evaporate hence appearing as everything is fine again...if a problem/leak does exist it will return.

If the unit works fine after resetting the power/breaker and soaking up any water present, it can likely be chalked up to a drain back-up or obstruction in the drain hose or pump...
\015\012 \015\012(it could mean a faulty drain pump so you'll need to pay close attention the next few times you run it)

...If not, there are a couple of other possibilities that I'd focus on.

**again insure power to the unit is off**

The first is the float and subsequently, float switch. If you've removed the service panel at the bottom, or toe plate, you need to locate the float and it's switch. It will be located directly behind where your main electrical junction is...

i.e.

macmarkus_4.jpg


Once you've located the float behind the main connection plate, you should see something like this image below,

i.e.


macmarkus_6.jpg

With the aid of a long screwdriver or if you can reach it, move the float up and down and listen closely for the switch to "click", indicating it is indeed functioning.

Restore power again, and see if this resolves the issue, if not try this next...

The pressure switch too can cause the drain/outlet pump to run constantly ( and usually all the lights to flash or "F2"...depending on the era and model of the Asko...ones with displays show F2 and leds flash, yours just having a mechanical timer show nothing ).


As I was saying the pressure switch is the component which controls the normal fill level and the overfill detection...pre float activation. The float is primarily the last ditch safety to prevent disaster in the event of a overflow, back-flow, or leak underneath the unit to service or call for service to the unit.

It too is located under the machine and is mounted to the sump well assembly as shown, the large arrow indicates the switch while the small is the hose.

i.e.

macmarkus_7.jpg


The issue is possibly just the hose going to the switch is clogged with debris such as dirt, detergent buildup etc and will be remedied by blowing it out.

The best way to do this is to remove this hose at the switch in the location indicated above, be very careful as to not break the hose off with the part of the switch inside, they can be delicate.

I typically work it loose with a tiny screw driver gently working it away from the switch. Once removed, pour a small amount of hot water, white vinegar or "CLR" through the sump from within the tub...or you can try blowing it through with "lung power".

The other end of the hose is located at the back of the sump well and is quite vulnerable to blockages over time due to detergents, dirt, and such.

This is the location...do not break this or you will need to replace the entire sump well...no fun.

Large arrow is pointing back to pressure switch, small indicates connection to sump well, sorry for the poor quality...it's hard to get in there with a camera phone, ha ha !

i.e.


macmarkus_8.jpg


That's almost the extent of the possible causes of this error. Of course it could be the pump as I alluded to, a pressure switch has failed, the float switch has failed, but not likely.

Hope this helps move you forward, or even better resolves the issue altogether. Let me know of course, I will help you move further if necessary.

Good luck.

Regards,

Macmarkus :)
Repair Help & Product Troubleshooting for Asko D1706 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ASKO D1706 drain pump will not stop running and the system will not advance to the next cycle even though the timer keeps spinning. What's happening here?


Hello,Welcome to FixYa.Based on your description "drain pump will not stop running and the system will not advan ... Asko D1706 Built-in Dishwasher

Nothing happens when the dishwasher is turned on for any cycle... the timer starts and keeps going but the motor - pump don't kick in... the time for the cycle expires and nothing has happened.


1.Listen for a humming sound.\015\0122. faulty motor, start relay. ... Frigidaire PLD2855RFC Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

At beginning of waswch cycle, water flows in. Then it stops and the cycle doesn't continue even though the countdown timer continues. Water flows out freely.


When the water comes in to dishwasher the wash pump should start if you hear a hummimg sound it means that the wash pump is either blocked or the capasitor on the pump is faulty or maybe the pump it self needs to be replaced ... Dishwashers

My 5 year old bosch dishwasher cycles to one minute and then cycles forever and ever with very soapy water in the bottom. After a very long time, the water is out of the dishwasher but soap residue is left on the dishes and the bottom ot the dishwasher.We are presently using only 1/2 teaspoon of detergent (Finish brand). I have had a repairman here to look at it, but he didn't seem confident that it was a timer issue and even though I have paid the exorbitant service call fee, I am not sure I wa


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

I have a Kenmore model 665. It is having an intermittent problem. It goes through the fill cycle, and then stops. Timer does not progress either. Then, at some random moment, it will come back on and finish the entire cycle. This could even be a day or two later. Sometimes it seems a nearby thump will set it off, other times no one is anywhere near it when it comes back on. This happened for a month or so off and on 6 months ago, and then it worked fine for 6 months. Now it's back to it.


Its possible its a door switch thats causing this or the main wire is loose..be careful as you do have 115 volts. i'd turn off power and check where power comes into d/.w and make sure the wire nuts are tight.. the next step is a little more difficul ... Dishwashers

Hi, My dishwasher keeps stopping mid cycle and the door pops open. The soapy water is always gathered in the bottom and there's no way for me to get rid of the water, unless i restart the full cycle. The dishes are all getting stained with white marks, even though the salt and rinse aid is filled. Please help!


Sounds like the latch is worn out you mabe able to get a new one at appliancezone.com.... also check the drain for debris ... Baumatic 23 in. BDW9 Built-in Dishwasher

Dishwasher will fill and goes thru wash cycle fine, But even though the timer will continue to rotate,motor will not run or hum in drain cycle.


Http://www.repairclinic.com/Dishwasher-Troubleshooting\015\012\015\012 ... GE Dishwashers

I have a Fisher and Paykel dishdrawer model ds603. Not sure eactly what happened but my son says that the cycle stopped last evening (and only tells me this morning!). Dishes though appeared to be clean and there was a small amount of water at the bottom. I tried opeing the washer and it was hard to open as though the drawer was stuck on something. I removed the drawer and checked the rollers and they are fine. I realised then that the drawer is getting stuck on the inside lid that provides the


The best thing to do is to remove the rack,drawer completly,and close it up,see if it will come on,and run all threw the cycle.If it does,then put the rack,drawer on the track.The rollers could be,well,not snapped all the way on.It will be in that ar ... Fisher Dishwashers

It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???


Check water valve to see if it has something blocking water supply ... Dishwashers

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

My beko DWD8650 dishwasher has stopped working - when I switch on the power, the machine sounds as though it is trying to work, even though the start button has not been pressed. Once the start button is pressed, the timer does not count down and nothing else happens.


... Dishwashers

I have a KDS-18 dishwasher, and had been working fine until recently. Now it keeps going into a Sani cycle even though I have selected normal wash. Anyway to reset the unit?


In your onwer mannual there is a number call kitchen aid they will walk you through the steps to reset your unit ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Bosche 4803 dishwasher, fills, drains but water not reaching wash arms during the cycle, even though I do hear the motor for when it should be happening. Have cancelled drain and restarted multiple times. Checked filters, removed wash arms and verified cleanliness and water passage.


... Bosch 23 in. SHU303 Built-in Dishwasher

I have a whirlpool gold quiet partner iv model gu2700xtss1 that was working fine until yesterday. When I start any cycle the dishwasher fills with water but the status bar just keeps spinning and will not go to a timer and the motor won't engage. Any ideas?


Hi,\015\012That would mean that the brain has gone wacky....there is a box in the top of the door that runs the whole show there.. if that goes nothing happens...\015\012You can find a replacement very easily...\015\012\015\01 ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

Hello, my hotpoint ultima FDW85 keeps coming up with a H20 error code, even though the water s getting through ok it stops partway through a cycle, how can i repair this? Many thanks.


... Dishwashers

Won't Stop My dishwasher has only been used about four times but when I switch it on, it will go on an on for hours and hours until eventually we just have to switch it off. It doesn't dry the dishes just continously sprays water on them. The timer runs down but then just goes back up and starts again as though it keeps repeating the cycle.


If your dishwasher's cycle times are too long, check these:Water pre-heatingCycle not completingWater pre-heatingYour dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the ... Neff 24 in. S5456 Built-in Dishwasher

I have an aeg favorit4001ovi dishwasher and the beeping alarm keeps going off not long after cycle starts it doesn't even get to the point where the tab gets used. this happens alot have had engineer out and suggested that the sprinkler jets are blocked. have checked and checked these, nothing in them. cannot get it to complete a wash at moment . only just over a year old!


... AEG Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

Wont run I have a Kenmore QuietGaurd2 it will not run at all. It filled up with hot water, then it quit working. It wont even drain the water out or cycle. Nothing is happening, whats wrong with my dishwasher??


... Kenmore 24 in. 15992 Built-in Dishwasher

My whirlpool quiet partner 2 dishwasher the clean button keeps flashing even though the dishes are not clean. Will not reset and I don't think it finished its cycle.


Same with mine. ... Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

I have a model SHE 44 C05 UC/40. It is three years old. It starts up fine, fills with water and goes into the wash cycle. Then it continues to wash indefinitely, even though the electronic timer display counts down to 1 and sets there. It still continues washing until you turn it off with the power button


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1544 seconds