Having problems with your Asko D1796FI Built-in Dishwasher ?

Asko D1796 will not start properly

\015 My Asko D1796 all of a sudden after 3 years of flawless operation will not start. I turn the power on, select the cycle and start it. It makes the draining noise for a few seconds and instead of filling up with water, the heating element comes on. I've tried turning it on and off. Cutting the power at the circuit breaker and it doesn't change. Even if I select the rinse and hold cycle with no heat involved it does the exact same thing and the heating element comes on. Please help. I just had a party and my dishwasher is full and my 3 year warranty just expired. What happened?\015

Answers :

It sounds as if you may have A bad control board. It could be causing the heater element to come on when its not supposed to (usually a stuck relay) and not filling the machine with water. you could also have a bad control board AND a bad fill valve, as a stuck relay for the heater shouldn't affect the fill valve circuit. The bad news is that these asko control boards are $350 to $450 for just the part, the good news is that the control board is under a 5 year warranty (for only the part, not the labor to change it) as are the pump motors and any timers. Also, if you are just out of warranty, find your date of installation, as asko warranties start when you install it, not when you buy it (if you moved into the house and it was there when you moved in, and you are the first owner, submit a date of occupancy and that's when your warranty started)
Repair Help & Product Troubleshooting for Asko D1796FI Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Asko D1796 will not start properly


It sounds as if you may have A bad control board. It could be causing the heater element to come on when its not supposed to (usually a stuck relay) and not filling the machine with water. you could also have a bad control board AND a bad fill valve, ... Asko D1796FI Built-in Dishwasher

Our Asko dishwasher no longer cleans the top shelf of dishes properly. Fine white and black grit is left on the dishes after every wash, and if there is any food residue on the dishes it does not come off. In addition, food residue that was not on the dishes to start with is being thrown up onto the top shelf and doesn't clean off the dishes. The control unit was replaced 2 months ago at vast expense, and this problem only arose following the repair. The only suggestion from Asko to fix the new


The problem is most likely that there is still water residue at the bottom of your machine. If the machine is not fully drained it picks up some of the residue and sprays that onto the dishes during the final rinse, leaving an unhealthy and un ... Asko 24 in. D3350 Dishwasher

Asko d1796 lights flashing won't start - Asko D1796FI Built-in Dishwasher


... Asko D1796FI Built-in Dishwasher

ASKO D1796 dishwasher start button is cracked


... Asko D1796FI Built-in Dishwasher

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

ASKO D1796 pump keeps running and cycle doesn't start


... Asko D1796FI Built-in Dishwasher

My Asko D1606 doesn't seem to be filling/retaining enough water to pump actively through the swing arms. When I add a litre or so of water in manually and hold in the door catch, I can see it appear to start working properly. The tablet is still sitting on the bottom of the dishwasher after the cycle has ended and the dishes are still dirty. The pump sounds all right and it is emptying fine. Also, probably due to the lack of water, the cutlery basket has melted right through, and I am sure any p


Check to see it the dishwasher has been pushed back ever so slightly. The water coming into dishwashers and exiting are on timers and if the hose is pinched this can affect it. Your dishwasher may appear to be in the same place but just pull it forw ... Dishwashers

Asko 1385: 13 year old dishwasher stops during cycle. If you push on the middle of the door it starts again. It is like the latch is not working properly but by all appearances the latch works fine. Troubleshooting ideas?


When you latch the door it closes the circuit.\015\012you may have to open the casing of the door to access the switch. it may be stuck or defective. ... Asko 1385 Dishwasher

ASKO D1796 won't drain


... Asko D1796FI Built-in Dishwasher

ASKO 1595 Dear greendude, thank you for your reply! i haven't checked the solution yet but wanted to specify: i've got ASKO 1595 and have had it for 4 years. recent year it started to mulfunction: sometimes it would stop in the middle of draining cycle and fault light would flash. this could be normally fixed by unpluging power cord, waitng for a few minutes and pluging power back again. wahat happened now is the different: dishwasher came on on its own, nowbody started it. it came on (draining


Yes have you tried what i suggested yet ... Asko D1776 Stainless Steel Built-in Dishwasher

My GE 2800 model dishwasher is not starting properly. When you start any cycle the water appears to be flowing in very slowly with no pumping action taking place. This dishwasher is approximately 15 years old and for the last several years I have suspected some problem with the electronics as certain cycles would not run properly.


Hi \015\012 \015\012Check to see if there's good water volume coming through the hoses attached to the washing machine. If there is, check to see if the screens inside the water-inlet valve are clea ... Dishwashers

Maytag dishwasher MDB7609AWW2 all the lights come on properly hit the start key and will start for about 30 seconds and then shut off then will not start again. Thought it was in store demo mode so reset that still not working when pressing the start key. Any ideas already tried reseting with the circuit breaker.


... Maytag Dishwashers

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

I have brand new whirlpool ADG7561 that has only been used a few times, without issue and it now will not start the cycle properly. It seems to start and can hear water filling then after a few minutes it stops and beeps 3/4 times. I have no flashing error light by the start button.


... Whirlpool ADG 7561 Dishwasher

Hi. I have a "Dishdrawer" F & P dishwasher DS603 range. I cannot start it to ceommence running a wash. There is no error code flashing, the power is on, and the door is closed properly. Whan i press start, it makes 3-beeps and simply does not start. I have tried turning it off, but this did not fix it


... Fisher and Paykel Dishwashers

Indesit IDL 705 dishwasher, when i start my machine it starts properly, but after 3 to 5 minutes pre wash and rinse bottom starts blinking repidly, i cleaned filter but its the same, please help me


Same issue here, also on a 705, gnerally accompanied by what looks like a short tripping the fusebox. ... Dishwashers

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

I just went to push start on my ASKO D3232 dishwasher and nothing happened. I can turn the machine off and on but it's frozen when on. I can't change the programming and the start button just flashes and won't start.


... Asko TouchProof D3232XL Stainless Steel Built-in Dishwasher

Asko,Asea1502 Dishwasher,when start the light start flashing on the panel


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Asko D1996 lights flashing washer won't start


I'm having the same issues. What did you do to solve yours? My start button never lights up! Thanks for your help! ... Asko D1776 Stainless Steel Built-in Dishwasher

Indesit dishwasher hi i have an indesit IDL40 slimline dishwasher which has developed a fault.It started by not cleaning the dishes properly and now it starts the cycle but stops shortly afterwards with lights 1 & 2 flashing.Please help.


Machine is flooded in base\015\012means you have a leak in dishwasher\015\012dismantle check feed pipe to top basked probable faulty feed pipe replace if so ... Dishwashers

My Asko D1976 dishwasher is not cleaning well, andmy Asko D1796 dishwasher is not cleaning well, and there are food particles and pooled water in the bottom. How do I clean this and/or fix the problem?


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Asko D1796FI Built-in Dishwasher

Hotpoint bfi620 The dishwasher starts washing. A few minutes later it stops and two of the green leds start flashing (the second one and the fourth one from the left). It has not been washing properly for the past few weeks. It will not complete a cycle at all now. can anyone help with this problem or can it be repaired


... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0718 seconds