Having problems with your Asko D1796FI Built-in Dishwasher ?

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Answers :

Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the counter by the sink or wherever. Undo the hose and see if it drains freely into a bucket, if so the drain to that point is clear. Insure it is clear beyond and move forward. Next, If you turn the power off and then remove the kick plate/toe panel ( that in itself is tricky if you've never done it, I can try to explain if need be...let me know ) then with aid of a flashlight or equivalent, check the overfill basin for water. If water is present, this will initiate the over fill float switch directly behind the main line junction block, hence the F2. ( of course a basin full of water can be from a faulty pump too, but you'll know this if the unit wouldn't drain into a bucket ) Then you must find the cause or leak, check the rubber hose at the top of the motor to the tub and the hose from the sump to the motor...it's tricky unless you've looked many times like I have and know what to look for. I wish I could guide you better from afar. Also look for sign's of leaking to the fill valve assembly. Another possible reason to overfill, a clogged pressure switch hose. Right beside the float and overfill switch assembly ( in fact it is wired right to it ) you'll see to the right on the sump assembly will be a pressure switch and hose. The switch will be about 1.5" in diameter with a brown color body and 4 brown wires going to it. At the bottom of the pressure switch will be a skinny black hose, remove the hose and clean it out via blowing through it or other means, it often will get plugged with undesolved detergent, food or other debris. It just comes off with carefully directly pulling force. This is what tell's the unit when to fill and when not to fill, hence if it is clogged it will not fill. Once the leak is found or the problem found, use a large sponge to soak up the water from the basin and the dishwasher should be ready to go.\015\012Those are several thing's to look for before changing part's to try and solve your problem. Let me know if I can assist you further. Thank you for visiting "fixya" today.\015\012\015\012P.S.\015\012\015\012Having said all this, if you feel at all uncomfortable performing anything I've laid out, please call a qualified "Asko" authorized pro to come to your home for service. They usually aren't serviced by many appliance repair places, at least not proficiently in my providing factory warranty experience.\015\012\015\012Thank's again and good luck.\015\012\015\012macmarkus :)
Check the water inlet valve,if its defective this will trigger an F2 code also
Repair Help & Product Troubleshooting for Asko D1796FI Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the ... Asko D1796FI Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Miele incognito dishwasher. The Optic indicator does not light up at all when the machine is started. The drain pump runs continuously. It is pumping out fine but the he drain indicator flashes. Filters checked OK. Water supply checked OK.


... Miele Incognito G818SCVi Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

GE model GSD600003 repair manual: Before you answer this, please tell me if I will be charged for the answer, in case I'm not interested at this time. Do you have a diagram of the drain area and water inlet area? I took apart the plastic drain cover for cleaning because it was had pink mildew all around it where residual water pools. I cleaned it all up and put it back and now the dishwasher doesn't fill with water (none comes in). I'm just a guest trying to troubleshoot for relatives, so I'm


I'm not sure how mildew can grow in a dishwasher that is working well, but after cleaning it and putting things back together, it does now seem to be working. I thought that the water wasn't filling but I guess the heating element heats up before the ... GE Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Zanussi zdt6053 will not fill with water, on any programme, it appears to try to start and makes a moise as if pumping, but there is not water to drain, and pump appears to operate if water is poured into the machine


Check float valve. It is probably stuck. This tells yuor machine to pump the water out and keeps the water valve from opening. Often it is something small that was placed in the dishwasher and lodges under the float telling machine that it is full ... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a KitchenAid KDS-17E dishwasher, which has worked well since I acquired it second-hand in 1984. Last night it ran continuously, stuck in the prewash part of fullcycle, with water being pumped through the system, and was fairly warm in the morning. It drained normally when I pressed the Cancel/drain button. I tried the machine again in full cycle. After 20 minutes it was still stuck in prewash, with the water temperature about 42 C, so I stopped it. Machine is connected to cold wate


Your problem is a bad timer.and you really got your moneys worth on this dishwasher.The timers useally go much soon than this one 7-8 years is the norm.The timer gets stuck in one position is a good sign its loseing its ability to fuction normally, ... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

I have a Teka DW6 55 FI Dishwasher which as the following fault, The frist 4 cycle indicator lights are on and it beeps about 6 or 7 times and the water pump is running,It then starts beeping again, all the time the pump is running.It dose empty the water.I tried holding down the program key and turning on but that didnt clear the error. Many Thanks Paul Luhman


... Dishwashers

Kitchenaid dishwasher The clean light was flashing 7 times, so I did read and try the solution SaniRinse-EnergySaverDry-SaniRinse-EnergySaverDry and this did get the machine to unlock and start up. Thank you! But I'm noticing that no watre is going into the machine. I can hear it drain some water. It is very hot and steamy in the machine so no heater problem, but I don;t see any of the soap on the bottom of the machine rinsing away. I'm afraid its stopping because the motor is overh


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1498 seconds