Having problems with your Asko D3432XLSS Stainless Steel Dishwasher ?

My dishwasher does not cut out when I open the door during the wash cycle


Answers :

Hello,\015\012\015\012This has been a common accurance with Asko dishwasher's since they went to this design around 1994 or so. If it won't stop when you open the door as you stated, here's a possible remedy you can try on your own. Make sure the unit is off first. ( this procedure is usually done by us Asko service guys by removing the door panel & control panel for better access as well as to visually inspect other component. but I'd rather keep it simple here ) Open the door and identify the small round shaped plastic item where the "latch strike plate" contact's slot in the top of the door. It will require applying a small amount of "vasaline" or "silicon lube" (**Do not use a WD-40 or any liquid type lubes that may cause a short circuit**) if you have any. Once you have applied the lube try to work it into the round "pin" ( simply put this is the little pin which actuates the microswitch in the door to comunicate to the control "GO" but it dry's up and sticks the switch "closed" ) so it moves freely up and down. You can apply the lube with a toothpick and then open & close the door several times, but it may indeed require taking the door panel off to access the entire assembly for a good lube. This should get it working properly for you again, or it may actually be a faulty door switch although when they fail it is typically in to "open" position therefore rendering the unit non functioning. \015\012\015\012Let me know if you require further assistance. Thanks for coming to fixya, please take a moment to rate the help you received.\015\012\015\012Good luck.\015\012\015\012Macmarkus :)
Repair Help & Product Troubleshooting for Asko D3432XLSS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have an AEG 44050 VI dishwasher. The door will not now close (it will not activate the lock mechanism) yet the machine will run a wash cycle and not cut off because the door is open.


... AEG 24 in. Favorit 44050 Built-in Dishwasher

Is there a way to have this dishwasher continue the wash cycle automatically after the door is opened? The kids always forget to press the start/resume button after opening the door during a wash cycle. This is for a KitchenAid KUDT03ST model dishwasher.


... KitchenAid Architect® Series II KUDT03ST Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher does not cut out when I open the door during the wash cycle


Hello,\015\012\015\012This has been a common accurance with Asko dishwasher's since they went to this design around 1994 or so. If it won't stop when you open the door as you stated, here's a possible remedy you can try on your own. Make sure the uni ... Asko D3432XLSS Stainless Steel Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

Soap dipenser My whirlpool built-in dishwasher model DU930PWPB0 serial # FR4104078. The door to the soap dispenser will not open. I have been washing the dishes with the door open all the time. When I close it(door) it won't pop open when it should. to dispense the soap in the wash cycle.


Try this... Wipe out the soap dish with white vinegar and a soft cloth.. make sure you get everything off the edges of the door and look for any nicks, blemishes or deformation of the dispenser door to make sure it is not mechanically binding up when ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

I HAVE A BUILTIN KITCHENAID SUERA DISHWASHER WHICH IS ABOUT 14 YEARS OLD IT SEEMS TO WORK PRETTY WELL. BUT THE SOAP DISPNSER DORRS TICK CLOSED SO THE DISHWASHER FINISHED AND THE DOORS REMAND CLOSE SO THE ONLY WASHING IS DONE WITH WATER AND NO SOAP. THE SOAR DOOR HAS TWO SLIDING DOOR THAT ARE ARC SHAPPED AND SEEME TO BE CONECTED WITH BUTTONS ATH THE CENTER. THE SOAP DISPENSER ID AHITE INJECTION MOLDED PLASTIC ANDY IDEA I CAN TRY TO GET THEM TO OPEN DURING WASHING CYCLE THANKS **** VON ROTH


Water does not come into the washer ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

My dishes have a film and sometimes have mould on them after they've been run through the wash cycle. All my dishes are practically clean when the dishwasher is run and we open the door as soon as the cycle is done. Anyone have any solutions? Is it safe to run an empty wash cycle with bleach instead of dishwasher detergent?


Try using some orange tang drink crystals...sounds odd but works really well.. your dish washer will look like new inside ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

I have a gibson dishwasher, age unknown, that developed a problem with the soap dispenser. During the wash cycle the soap lid doesn't open until late and a gooey soap mess is left on the door. Any suggestions? the dispenser is always open when the dishwasher is finished however the detergent if liguid is a mess on the door and the closest dishes or if a block - still a block in the bottom of the dishwasher -


Run it a few times with a soap tablet in the cutlery basket. The door is just sticking and doing this normally cleans them up. ... GE Nautilus 24" Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

My whirlpool dishwasher type 280-2 detergent door will not open during wash cycle. Yes the compartment, springs and door are thoroughly clean. Will not open if I just close the door and remains empty. I'm wondering if perhaps I knocked off some random part that makes it open. So please tell me how darn thing opens and perhaps a pic of the parts so I could see if ones missing. Thank you for any help offered for this, its driving me nuts.


... Dishwashers

We recently installed a Kenmore dishwasher, Mfr Model# 13943. We have used the dishwasher approximately six times since Thanksgiving. Each time, after the wash cycle is complete, when we open the door, water has collected on the interior of the door, and water remains standing on some of the washed dishes. Is this normal?


... Kenmore Dishwashers

My daughter put the wrong detergent in the dishwasher (!). Now its stuck in drain cycle. If I put it onto wash cycle I can hear it draining even with the door open, but when I shut the door it doesn't go to wash and the bottom fills up with water. Thanks!!!


Hi,You need to find the bottle of white vinegar or cooking oil, if you have one...that will cut the suds and get you working again...Check this out...http://www.acmehowto.com/howto/appliance/dishwasher/wrongsoap.ph ... Bosch Dishwashers

Whirlpool Dishwasher detergent door not operating properly. Main wash door opens immediately after starting dishwasher. No pre wash cycle. Loud humming noise coming from bi-metal switch or wax motor attached to the detergent cup assembly. I just replaced detergent cup assembly including the wax motor and I still get a loud vibrating humm from the actuator. model number du1055xtp3


Pdemaio,ngafm at your serviceI believe the loud humming you describe is an electronic problem. And is not worth changing parts randomly and spending unnecessary funds in this fashion!my advice is a hands on experi ... Whirlpool Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2272 seconds