Having problems with your Asko D5152XXLS Dishwasher ?

I have an Asko 1485 Dishwasher. It is showing a F2 code.


Answers :

Hello, welcome to FixYa.

Based on your post, "Asko 1485 Dishwasher. It is showing a F2 code", the good news...It is likely nothing very serious, but the "resolve" requires some investigation on your part.

What the F2 means is the control has indicated a overfill.


**before proceeding turn the dishwasher power off via the home breaker panel, or unplug it from the wall if that is possible...most are hard wired to the home electrical...safety first**

The first thing to do is remove the toe panel/kick plate and inspect the base for water. There will likely be water present.

With the aid of a sponge, towels, or a wet-dry shop vacuum, absorb the water from the base, that should restore normal operation...it should be known that if you leave the unit for a few days, the water in the base will evaporate hence appearing as everything is fine again...if any other problem/leak does exist it will return.

If the unit works fine after resetting the power/breaker and soaking up any water present, it can likely be chalked up to a drain back-up or obstruction in the drain hose or pump...
(it could mean a faulty drain pump so you'll need to pay close attention the next few times you run it)

**The float is primarily the last ditch safety to prevent disaster in the event of a overflow, back-flow, or leak underneath the unit and the illuminated
F2 letting you know to service or call for service to the unit**

Hope this helps move you forward, or even better resolves the issue altogether. Let me know of course, I will help you move further if necessary. Good luck.

Regards,

Macmarkus :)
Repair Help & Product Troubleshooting for Asko D5152XXLS Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Asko 1485 Dishwasher. It is showing a F2 code.


Hello, welcome to FixYa.Based on your post ... Asko D5152XXLS Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

Asko dishwasher d3251 diverter valve code? - Asko D3251HDSS Stainless Steel Built-in Dishwasher


... Asko D3251HDSS Stainless Steel Built-in Dishwasher

Asko dishwasher error code f10 - Asko 24 in. 1895 Built-in Dishwasher


... Asko 24 in. 1895 Built-in Dishwasher

Asko dishwasher 2000 error code F2 and F7 - Asko Dishwashers


... Asko Dishwashers

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

When exterior breaker panel was replaced, my Frigidaire dishwasher (model FDB989GFC2) was accidently wired to 2 breakers and briefly took a 200v load. It started, then immediately showed a Power Failure code and shut off. The wiring has since been corrected but the dishwasher now shows no signs of life. Is it terminal or can replcement parts solve the problem?


Hi\015\012\015\012\015\012Thanks for using FixYa. You’ll need to check the following things--\015\012\015\0121. Fuse (blown or tripped).\015\0122. Check the wire fasteners at dishwasher junction box. ... Frigidaire Dishwashers

What does the error code LE mean on my LG Dishwasher Model LDS5811ST mean? Dishwasher makes noise in the rinse cycle and at end of cycle LE error code shows in window.


MAin wash motor needs replacing\015\012\015\012Affordable Appliance Repair\015\012Lake Forest, CA 92630 ... Dishwashers

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

ASKO dishwasher - F2 code - what could be leaking??


... Dishwashers

H:01 code The dishwasher is showing a h:01 code and will not start. What does this code mean?


... Bosch She6Ap02Uc Ascenta Evolution Series 24" Built-In Dishwasher

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

F2 code on Asko D-1776 dishwasher


Hi.F2 means high water level. There is an overfill sensor located on the bottom pan that can be triggering the error code.Try first tripping the circuit breaker and see if this can clear the error message. ... Asko D1776 Built-in Dishwasher

Haier dishwasher wont run and shows a code OP


The code "OP" means the door is open. I would suspect you have a faulty latch. The dishwasher thinks the door is open and will not start the cycle. ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

My Asko dishwasher is not draining. Code F2


Drain plugged, hose kinked or discharge pump bad ... Asko D1976 Built-in Dishwasher

Top dishwasher codes f 1 & shows picture of wrench bottom unit works fine it is a fisher&paykel


Forums.whirlpool.net.au/archive/584206 give this a go. has a few solutions ... Dishwashers

Asko dishwasher error code lh or 1h


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Neff dishwasher not running, showing error code e25 and e17


... Neff Dishwashers

My bosch dishwasher model no SKS60E02EU is showing error code 14


... Dishwashers

Dishwasher is showing a f11 code


... Asko Dishwashers

Codes Hi, my dishwasher keeps showing me either F7 or F9 when it doesn't want to work. Yet sometimes it works perfectly. Can you please tell me what these codes mean. Thanks


IDEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012I am happy to be of assistance!\015\012\015\012\015\012 ... Dishwashers

Smeg Dishwasher smx shows programme code PC Won't allow any other programme codes


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1922 seconds