Having problems with your Asko Dishwashers ?

D3350 F4 indicator

\015 Model D3350. F4 indicatoris flashing. Phone tech says it's a water supply issue.\015

Answers :

F4 This is a Fault with the water fill

Note: Lights blinking, pump running and controls dead indicates an over fill fault

1. Disconnect the power to the unit

2. Remove the lower access panels and check the tray under the dishwasher (you will probably find that it is full of water)

3. Use a towel or a sponge to remove the water

4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional

5. Test the dishwasher

6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink

7. The drain hose must run up to the top of the underside of the counter top then down to the drain. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray

Repair Help & Product Troubleshooting for Asko Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

D3350 F4 indicator


F4 This is a Fault with the water fill Note: Lights blinking, pump running and controls dead indicates an over fill fault1. Disconnect the power to the unit2. Remove the lower access panels and check the tray under ... Asko Dishwashers

Model no. MDB6100AWW. Just unloaded the dishwasher. Shut the door and immediately heard clicking (regular cadence). All indicator lights (arrow-shaped) for clean, dry, wash and heating delay were blinking. Opened the door, waited a few minutes, closed the door. Now, just the "Clean" and "6 Hour" arrow indicator lights and "Heated Dry" button light indicator are still blinking continuously. Cannot override. What's going on? Dishwasher came with the house when we purchased it 6 years ago. Proba


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash-heated dry ... Maytag 24 in. MDB6100A Built-in Dishwasher

After interrupting a wash cycle by opening the door, the "start" button indicator will not light when the start button is depressed. (Neither will the "delayed start" indicator work.) The dishwasher will not resume any operation. All other control indicators light when selected. Removing and restoring power to the unit does not clear the problem. The unit is a Jenn-Air model JDB1100AWB.


It is possible that by opening the door mid cycle, the door switch mechanism has got disengaged. Refer item 11 in ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

Kenmore model 5871526 When wash cycle is selected and start button is pressed, the wash cycle indicator, heated dry indicator and the Washing cycle indicator lights flash continuously - but the dishwasher does not start


... Kenmore Dishwashers

LED indicator There is a LED indicator above a tag or lock symbol with the letter "B" it is lit and the machine will not work. I have misplaced my manual and do not know what the indicator is for. Can anyone help?


Sounds like the control lock feature has been activated. look closley at the buttons one with the" lock" light hold in for 3 to 5 secs and it should dissapear ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Boash she4amo Getting a Sensor Error (FS) E:06 when running the Customer Service Program....indicated by the CLEAN led status being lit....thought it was a door sensor failure (chart indicates "door" in the chart beside this failure....but further testing indicates the unit knows if I open the door, and stops the program, so it isn't that.


... Dishwashers

The dishwasher is in the middle of the cycle air dry indicator goes out lock indicator goes air dry goes out. Then dishwasher hesitates lock light goes out air dry indicator comes on. This is repeated throughout the cycle


... Kenmore 15634 Built-in Dishwasher

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

PF indication I get an intermittant PF indication and the wash cycle stalls and machine beeps


You are having a power issue with the plug outlet or the junction box at the bottom right of the dishwasher.  To be sure, run an extension cord and use a different outlet in the kitchen.  If after a couple of loads, the PF problem doesn't c ... LG 24 in. LDF7810 Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Model Ariston AFA370X - This query is for my daughter who is currently house sitting and can't find any manual for the machine. When switching the dishwasher on there are two red lights next to the on switch. One light indicates salt but it's the other light that is coming on with 2 stars above it and she doesn't know what this light indicates. She has used the machine once before and everything seemed fine but this time this light keeps coming up and the machine will not start. Please a


... Dishwashers

Miele incognito dishwasher. The Optic indicator does not light up at all when the machine is started. The drain pump runs continuously. It is pumping out fine but the he drain indicator flashes. Filters checked OK. Water supply checked OK.


... Miele Incognito G818SCVi Built-in Dishwasher

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

My Siemens dishwasher SE65M350EU/70 has an error about once a week: it washes perfect but during the last step (rinsing/drying) it sometimes stops/ continues a number of times and then indicates a low water pressure error. But never during the other steps of the washing cycle. To me this indicates that the water pressure is correct. Any idea?


... Siemens 24 in. SE26293 Free-Standing Dishwasher

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

My Frigidaire PLD4460REC0 dishwasher status indicator is completely black. The window used to have a green display with the cycle timer. The dishwasher seems to be working fine and I can even change cycles but the status indicator is blank.


Hi\015\012\015\012First make sure that nothing is blocking the drain pump\015\012assembly located inside the lower front panel of the dishwasher. If the issue\015\012returns after its cleaned then try to reset the dishwasher control by pr ... Dishwashers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

I have a Siemens SE65560/12,I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was ''I'' indicated, or maybe means ''1''. Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling MoreI have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was ''I'' indicated, or maybe means ''1''. Now


... Siemens Dishwashers

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

My cda CW195/1 dishwasher keeps running for 5 mins then beeping, salt indicator was flashing but have now filled up and the indicator has gone off, i have cleaned the filter, turned off and on and tried on a high setting but it still it beeping like there is a problem!


I am having the same problem. It's a piece of rubbish. ... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Zanussi dishwasher model IT 5614. When I turn the dishwasher on, the indicator light is already stuck at "BIO 50" and won't move, and the dishwasher won't start when the door is closed. This just happened today. The indicator light for dishwasher salt was also on, so I added dishwasher salt and that light went off, but the machine is still stuck. The instruction book says that when this happens, technical assistance is needed. What exactly is the problem, and is it anything I can


It has been suggested to switch the machine on/off a couple of times and the flashing light will not reappear. Until this light goes off the dishwasher will not start. All the filters should be cleaned free of any leftover food particles. What i mean ... Dishwashers

Reset Button When I plug into outlet. I press the reset button the red indicator light will show but when I push the test button the red indicator light comes off. What does this mean I have a Karcher 1500 psi K2.25


Your testing the no fault short or motor overload feature. the red light indicates you have power. no light no power. ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0264 seconds