Having problems with your Asko Dishwashers ?

Smeg DF612SDX with an E8 fault that is consistent. Cannot identify the alternating valve if that is the problem?


Answers :

Repair Help & Product Troubleshooting for Asko Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smeg DF612SDX with an E8 fault that is consistent. Cannot identify the alternating valve if that is the problem?


... Asko Dishwashers

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

I have a 4yr old Smeg freestanding dishwasher. Model is DF612SDX. The problem is that a wash cycle will start but about 15 mins in it stops and 2 of the programme option lights (on the left hand side of the programme options), start flashing. If you open the machine the soap dispenser has failed to open. This problem has been a bit of a slow deterioration as we've had a number of washed that have managed to finish and then noticed that although the dispenser has opened it must have been to


... Smeg 24 in. DWF612SS Free-standing Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Smeg df612 dishwasher problem, lights up as a e2 fault ,i have tried draining the dishwasher but still the same problem . the salt container is full of water is this normal?. and how do i reset the machine . ive tried pressing the programme button 4 times but it just shifts through the different cycles . can you help please/.


... Smeg Dishwashers

Smeg dishwasher df612sdx water leaking looks like its coming from the water seperator valve can it be taken off and tested thanks Darren


... Smeg Dishwashers

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

Hoover dishwasher HOD 7715 fault code E2. no problem with water supply safety switch on inlet valve?


... Hoover Dishwashers

I have a Diplomat ADP 8520 dishwasher (possibly SMEG manufacture) which will not stop trying to empty. There are 4 leds lit reading left to right and it beeps. I have read on some forums about pressing the programme button 4 times or holding it down for ten seconds to clear the fault but neither of these solutions work. I thought maybe that the drain was blocked but I put the pipe directly into the sink and it empties ok, problem is, it does not stop.


Fault is probably water in the bottom tray operating the anti-flood device. take bottom front panel off and mop out the water and it will work. if fault reoccurs then you have a leak ... Dishwashers

Dishwasher won't switch on but fuse is ok? In fact each time we switch it on it trips the electric, have turned upside down etc, but cannot see any obvious problems, any ideas? Its a SMEG DWD912CSS. Thanks


As this is a serious electrical fault (live fault to earth) I would have an engineer check it over before using again. ... Smeg DWD612C Built-in Dishwasher

Our Miele Incognito G843 SCVi dishwasher was shipping backwater from the sink drain. I found a rubber band in the non-return valve that might have been preventing a seal of the ball joint. However, now I get the "Drain Fault" error when I try to run. Is there something I need to do to re-establish pressure first? Or is there some other problem?


You'r right on / ( shipping "? - like backing up from disposal or from sink .) the one way valve ( very common ) is used to prevent this type of problem . I would think that if rubber band held ( "non return valve open) then ... Dishwashers

I have a 10 year old Electrolux Dishlex Global 300. It doesn't complete a cycle, beeps many times then all lights go off and it stops. Then you cannot select a program to restart. It then beeps consistently throughout the day when not even in use. A repairman has tried adjusting electric wire connections, the door handle and checked for motherboard diagnostic faults (which shows nothing). Any ideas?


Hi mndl, it sounds like what happened to mine, it was the flood switch F1good luck slappa ... Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Hello, We have a Fisher Paykel DD603 dishwasher. I have spent $400 on parts and service call and still have same problem: U1 fault code. I have changed water inlet valve and electronic controller. I'm exasperated. Anyone with suggestions ? Jeff G.


... Dishwashers

Smeg df612sdx dishwasher wont drain


It is a common fault that the drain fails to work in\012most machines in a period of time and is the most problematic fault in a\012washing machine. In all occasions it is important that your observation is most\012important and so is vital ... Smeg Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hello I have a Maytag Quiet Series 300 dishwasher model #MDBH955AWW that is making a lot of noise. I saw an exchange on this site where the expert suggested filling the washer to just above the heating element, running it, and seeing if that solved the problem. I tried that and it solved the problem. I believe the expert said this indicates the fill valve needs to be replaced. Can you tell me which valve I need and advise me on how to change the valve? The manuals I have (Use & Care Guide and In


Http://sites.google.com/site/cwyffimsbffoe/maytag-dishwasher-parts-manual- ... Maytag Dishwashers

SMEG Dishwasher decor door problem


... Smeg Dishwashers

Problem with non-starting Smeg DWI 410 dishwasher - does anyone have a solution?


... Dishwashers

Smeg df612sdx dish washer - 'P' programme button not working


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

Zanussi zsf6126 dishwasher showing fault 3, water inlet not opening, not receiving power to valve. tracing circuit without diagram have tested both level switches and valve but no fault found there. can you help please?


... Zanussi Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1209 seconds