Having problems with your Bauknecht Dishwashers ?

My bauknecht dishwasher gsi 4743 is not working. When I turn it to the program the start light is already blinking and when I press start the end light flashes and the pump appears to run for a few seconds and then the whole thing stops but the startt light continues to flash. If you could help, I would really appreciate it. Thanks!


Answers :

Repair Help & Product Troubleshooting for Bauknecht Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bauknecht dishwasher gsi 4743 is not working. When I turn it to the program the start light is already blinking and when I press start the end light flashes and the pump appears to run for a few seconds and then the whole thing stops but the startt light continues to flash. If you could help, I would really appreciate it. Thanks!


... Bauknecht Dishwashers

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

Whirlpool ADP 5550 the start button continuously flashes twice and the rinse light is on. The pump starts but then stops and the lights keep flashing.


... Dishwashers

My GU 120 stops mid cycle and the indicator light starts blinking a humming whirring sound preceeds the ctcle stop nad light blinking. Pressing the button for 5 seconds causes the flashing light to extinguish but the sound continues untill the unit stops. It does not complete the full cycle. Your help would be appreciated. Tony


... Whirlpool Dishwashers

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

The dishwasher starts fine and then it will just shut down. The lights won't shine at all on the front. Then when you open the door there is water standing in the bottom. When you shut the door the green light start/resume starts flashing again. You start it again and then it does the whole thing all over again.....please help. I hate the thought of replacing it. Thanks! Whirpool Quite Partner II. DU1100XTP


Check how many times the light flashes. if it flashes 7 times you have a too cold water going in error. or you heater could be faulty ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Start the m/c it starts to fill on/off green light starts flashig machine stops light continues to flash


... Whirlpool DU851SWPS Built-in Dishwasher

Whirlpool ADG6962: The power light is flashing. When I push the power light and hold for a second, the machine seems to start it's drain cycle, but then stops and the power light continues to flash.


... Whirlpool Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Nordmende dish washer model no. DWSN60WH . when power button is switched on machine gives a buzzing noise for about 10 seconds while the start button is still lighting. Noise stops and light goes off and then wash and end buttons start flashing continuely.


... Dishwashers

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Baumatic BKD45W Push Start and pause And Standard lights flash and beep for about 10 seconds then beeping stops, lights continue flashing.


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

The start botton does not work when you push the sanitize, heat dry, and heater they light up once got it to start by pushing the stop button 3 or 4 timesand then the start button. but not any more. Any thing other than replacing the whole control under the cover sheet available? ?


... Whirlpool MDBH979AWS Builtin Dishwasher

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I have a kichenaid kuds03ftpa dishwasher after start it stops after several minutes and the start light flashes. When i open the door, there is water at the bottom. So i press cancel and the water drains out. Then i restart the dishwasher and it does the same thing.


... KitchenAid KUDS03FTPA Built-in Dishwasher

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1174 seconds