Having problems with your Bauknecht Dishwashers ?

My Bauknecht GSI 5033 stop working and green light is blinking above the Start button. Fiter has been cleaned and it didn't help.


Answers :

I am assuming by now you would have tried to turn the power to the dishwasher off and back on.
\015\012If that did not help, there could be a number of reasons.
\015\012Faulty Start button, thermal fuse blown, inlet water valve faulty, controller faulty.
\015\012
\015\012Does the flashing change if you keep the START button pressed for 5-6 secs?
Repair Help & Product Troubleshooting for Bauknecht Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

My Bauknecht GSI 5033 stop working and green light is blinking above the Start button. Fiter has been cleaned and it didn't help.


I am assuming by now you would have tried to turn the power to the dishwasher off and back on.\015\012If that did not help, there could be a number of reasons. \015\012Faulty Start button, thermal fuse blown, inlet water valve faulty, con ... Bauknecht Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so


... Smeg 18 in. DWD409SS Built-in Dishwasher

Hi I have a Kudso1flSS1 dishwasher. I just replaced the control board and the switch board assembly, the pump is recently replaced and the filter is clean. The start button keeps flashing and the water level is always low. The DW stops running after 15 minutes and the flashing starts again...... Help!


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Was running a wash cycle lastnight and it stopped running and the clean (green) light is blinking and won't turn off. When I push the Start button, there is a red blinking light. Help. It is a Kenmore Stock # 16033 Type 575-0 and Model 665.16033401.


Is your washer a front load? Does it have a small window where you read the stages or minutes left?\015\012If so is there a code flashing in thet window?\015\012Also what year is your model? ... Kenmore Dishwashers

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My fridgidaire is flashing the Washing, Sanitized, Clean, and the Sanitize button. It starts and acts like its ok and then it stops with those lights blinking. Can you please help?


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


... Sunbeam Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. Th ... Sunbeam SNB542UCAS Built-in Dishwasher

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

We have a DWF A10 and the light indicator flashes 2 times i have cleaned the filters ect presses the start button and held it in but all it dose is drain out and continues to flash can you help me or


... Dishwashers

Dishwasher stops at mid cycle. Starts blinking for 7 consecutive times stops and starts blinking again. A technician came and showed me how to reset by pushing different buttons and it will start again but only to stop once again. Please help. Email me at [email protected] Thank you Kitchen Aid KUDSO1FLSS6


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Frigidaire Dishwasher gld2440reb1. After removing filters, cleaning and replacing them I had three flashing lights ie Sensing, Clean and Sanitized. all buttons were inoperable. after unplugging and reconnecting I had a PF or power failure indicator. after pushing the start button the PF went off but no further action from any button. Help!


Usually if you get a PF error that means you have received a power failure usually from the control board shorting out on this model. Typical reasons the control will short out is from either the circulation motor shorting or pump motor shorting. If ... Frigidaire Dishwashers

How do I get my Bosch SHE4AM16UC dishwasher to pause and then start again at the same place it was in the cycle? I pushed the STOP button and then the START button and it started at step one. My dishes will be super clean, but all I wanted to do was pause it for a few minutes.


... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers

Please help my wirlpool ikea diswasher was working well but suddenly it stopped!I have one of those DWF small ones and have the buttons on the inside top part of the door. when I press the start button nothing happens and when I close the door the alarm sound goes off!! can anyone help me please


Try dropping power to the unit for a minute and see if it will reset itself. if not, you have a logic board failure. that or a door switch. check the manual for an indication on the warning alarm.good luckmark ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1752 seconds