Having problems with your Bauknecht Dishwashers ?

What does E8 and F1 error codes mean? We get this at the beginning of the cycle and the dishwasher shuts off?


Answers :

Repair Help & Product Troubleshooting for Bauknecht Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What does E8 and F1 error codes mean? We get this at the beginning of the cycle and the dishwasher shuts off?


... Bauknecht Dishwashers

Getting error code 1E I've replaced the sump pump, cleaned the screen at the water inlet, checked water flow from the hose. Continue to get the 1E once water has entered dishwasher and begins the wash cycle.


... LG 24 in. LDS 5811 Built-in Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have an LG dishwasher, model LDS 5811WW. Just after start up the error code "LE" comes on and the cycle shuts down. I have tried a couple of different cycles and they both react the same. Several other codes are found in the owners manual but not this one??


I'm just posting here to clear this from My Work Queue. There may be another cause for your code, but it only applies to certain serial numbers. If you want to know about it, do an ASK ME, otherwise good luck with your repair. Please don't bother ... Dishwashers

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a whirlpool aquasteam 6 series dishwasher and no matter what cycle i run i get error codes f8 and e1


... Whirlpool Dishwashers

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

My bosch dishwasher model shx45m runs for hours. It gets down to the last minute on the cycle time and then will not move on to the next cycle. The error code is 01.


... Bosch Integra 500 SHX45M0 Built-in Dishwasher

I just installed a new Frigidaire dishwasher. Took it through 1 cycle as the directions indicate looking for leaks. I now have it full of dishes for its maiden voyage, and I get an Er uo code. Cannot find this error code anywhere. Can someone help me. M# FGHD2433KW Jamie


This is a vent problem you need to check the vent motor and make sure tha the wire have not been pinched by the door spring and make sure it is connected properly.the vent should be located on the top or possibly the right side of the cabinet. ... Dishwashers

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

Danby Dishwasher DDW1806BSL Dishes weren't getting clean for awhile. Now, we get an E3 error code and it won't continue through the cycle. There are no repair services in our area for Danby. Help!


Fault Codes E3: Longer heating time, but required temp not met. Possible Causes: Malfunction of temp sensor or heating element. ... Danby DDW1806BSL Stainless Steel Built-in Dishwasher

My lg dishwasher is running ok but i randomly get the LE error code. I noticed that when it runs the cycle it takes 3 times as long to run than normal. Is this the motor or the electronic panel. the wiring is ok already checked.


Motor might have something blocked in the coils. mine did the same thing and found a piece of plastic melted in the motor housing ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Dishwasher- three years old, wont wash. the pump starts making a straining sound after a few minutes in any cycle, and then I get the E1 code. the machine does not shut down. Tom


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Error E1 is a leakage error\015\012which occurs due to excessive RPM of washing motor during wash cycle due to\ ... LG 24 in. LD-12BW5 Free-standing Dishwasher

I have a fridgidaire dishwasher, model PLD3460. Getting no water, cycle selector is stuck on on china setting. It did show an error code of EE. Any ideas?


... Frigidaire 24 in. PLD3460 Built-in Dishwasher

I have a fisher paykel dishdrawer dishwasher that i get a F1 error code then it shuts down i have dried up the bottom tray but it will only work for about 1 week and it does it again


Perhaps you need to find out the source of the problem. The F1 code is due to the flood switch at the base of the housing getting triggered by water collecting. You could have a cracked hose or broken actuator arm (this is piece of plastic at the bac ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I am currently getting an E1 error code on my Brada dishwasher, it sometimes works but it usually just stops abruptly during the cycle and beeps E1. Any help or recommendations would be greatly appreciated, cheers.


Youve got a block in the water coming into the unit, check down where the hoses retract into and look for a kinked hose. ... Dishwashers

Whirlpool ADP6000WH No Power up We started a cycle , then all of a Sudden it shut off completely.... No error code at all and no lights or Display. No fuses in the House were thrown and i've tested the power point on the wall and all is ok. Just no response when pressing the Power Button on the Dishwasher??? Please Help :)


... Dishwashers

What does the error code LE mean on my LG Dishwasher Model LDS5811ST mean? Dishwasher makes noise in the rinse cycle and at end of cycle LE error code shows in window.


MAin wash motor needs replacing\015\012\015\012Affordable Appliance Repair\015\012Lake Forest, CA 92630 ... Dishwashers

I'm getting an error code LE on the control panel and there is still water in the bottom of the dishwasher. The cycle was almost finished. What is the problem?


This is a drainage issue. check the following to address this issue.1. Air gap / Drain hoses If there is an air gap (located in\015\012the sink, near the faucet), check to see if it is clogged. Unscrew the\015\012top cap and ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Standing water in bottom of dishwasher--get F2 error code. It works if I drain all the water before cycle by using a turkey baster


Sounds like the drain pump on this unit is bad //you may luck out and tear into it and remove some debri from the impellar but they are made mostly of plastic these days and normally go bad... disconnect the drain hose from its termination point usua ... Asko Dishwashers

I have a dishdrawer (2) and following the use of a dishwasher cleaner, the bottom drawer appears to have developed a blockage. It will not empty, gets to the pump out part of the cycle and shows the red error code F3, to which there is no reference in the trouble shooting guide. The top drawer has also developed minute leak, sufficient enough to leave dribble marks on the lower drawer and over time, a white deposit on the floor. Is there anything we can do for the blockage problem before reso


Remove the small basket from each drawer and lift up the removable plastic cover and take the drain filters out , empty them of food by products and try it again.. If you've never cleaned them then that's your problem with the drain process.. Hope th ... Fisher and Paykel Dishwashers

Getting error code 0E on LD-14AW3 model dishwasher after 2 minutes. Checked drain hose and water seems to be coming out but won'y go any further in cycle Also makes a loud humming noise when running.


To little info, but looks like pipe is much to low. Not getting the opportunity to fill up properly.Raise it higher.(Im asuming that you can hear the drain pump run and water is being pumped out as wall. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2547 seconds