Having problems with your Baumatic 23 in. BDW13 Built-in Dishwasher ?

Looking for reset switch

\015 Looking for the reset switch on the baumatic bdw 3wthe water is not heating and i want to give it a reset beforei try a new element have taken the foot plate off and there is a fuse but no sign of a reset swithc , can anyone help ..ta d\015

Answers :

If your getting `E3` then it cannot be reset, one of the two thermostats on the heater element cannot be reset and has to be replaced, around £18, you can test which one of the thermostats is faulty by using an `ohms` tester, open circuit, faulty, this is a very common problem with these.
Repair Help & Product Troubleshooting for Baumatic 23 in. BDW13 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Looking for reset switch


If your getting `E3` then it cannot be reset, one of the two thermostats on the heater element cannot be reset and has to be replaced, around £18, you can test which one of the thermostats is faulty by using an `ohms` tester, open circuit, faul ... Baumatic 23 in. BDW13 Built-in Dishwasher

No power to the starter, is there a cut of switch or reset button i should look for


... Karcher Pressure Washers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug, GFI and circuit breaker switch. Still no power and no light no response from various buttons.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012It sounds like you've got a bad power switch or a wire at the power switch or as you described it... (circle with a I, looks like a reset button?) ... Asko 24 in. D3530FI Built-in Dishwasher

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug and circuit breaker switch


Hello Rick,\015\012make sure you have tested the unit with the door closed all the way ,make sure the delay option is not turned on make sure the power cord is properly plugged into the outlet, and check your fuse box for any blown circuits sor ... Asko D3531XLHDSS Stainless Steel Built-in Dishwasher

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

My kenmore dishwasher 665.17052400 clean light is flashing 7 times. I cannot locate the tech sheet to find out what is wrong. I have reset the panel and it will run then blink again after 15 mins or so. I have also done a hard reset and looked at the heating element, but it looks fine. Please help.


... Kenmore Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Our KitchenAid dishwasher (Model KUDP01ILBt6) doesn't run unless I turn off the breaker switch for 30 minutes, which is suppose to reset the washer. The next load will run, but then the same prob


... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Asko d1876 is there a reset switch? i have cleaned lines, drain and no water anywhere-- f2 still flashing-- any reset switch other than circut breaker?


I have a D1876 it stopped draining in cycle all lights flashing and F2 . anyone know what to do ... Asko D1876 Dishwasher

Double dash on display and when put in service/maintenance mode, all the lights came on and stayed on overnight. Still not working until I tested the door switch. It looks like poor engineering on the design. Plastic bar that depressed the door switch was not pushing all the way. It appears that the bar was bent to compensate for the too close tolerances and after the depressing of the switch for six years it did not reach anymore. So I got hair dryer, heated the plastic bar and bent it down to


... Kenmore 24 in. 15932 Built-in Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Hi can you help me please I have a Zanussi DX6453 dishwasher which has stopped working. Having used the diagnostic facility it has come up with anti flood device, I have done the usual rocking the machine back and forth no sign of water. I have taken the machine apart and looked at the anti flood switch and this is bone dry and by lifting the float you can hear the switch clicking on and off. When I reassemble the fault is still there I'm begining to think the switch is faulty but not sure, do


... Zanussi 23 in. ZDT6255 Built-In Dishwasher

Karcher K3.92 M 1750 PSI poweer Washer motor won't start. Followed Reset/Test/Reset sequence with cord plugged directly into outlet. Light on cord near Reset comes on when Reset pressed down but goes off when Reset released (Normal?) Switch ON and trigger pressed releases water stream but no motor action.


They are sensitive to large extention cords. My father in laws pops reset when a small cord is used. If internally shorted- motor will continually pop the reset even plugged direct to outlet. Check voltage at outlet. ... Karcher 2500 PSI Pressure Washer

Dishwasher problem Our Asko 1353 dishwasher stops halfway through its's wash cycle. I suspected the thermostat, as it seemed loose in it's holder and not tight against the tub. After I tightened the holder the problem is still the same. Also, the on/off switch (pressure switch?) does not stay in the on position and when I looked it over I found one of the crimp on terminals had melted. Short circuit? Too much resistance from bad thermostat? How do I check the thermostat before I order a new one?


I think your switch may just be bad,but to check the t-stat remove both wires and use a multimeter,set the meter to ohms and connect the two leads to the terminals on the t-stat.with the t-stat to off you should read an (ol) open condition,when you t ... Dishwashers

Bosch Dishwasher SGS43E02 Exxcel. Switches on at main switch (0 appears in the numerical display) but none of the right hand programme buttons seem to be working! Have checked filter on water supply hose and that doesn't look blocked.


Obviously a faulty connection. Lots of switching off and on and holding down the buttons eventually sorted it! ... Bosch 24 in. SGS43E02 Exxcel Built-In Dishwasher

I have a Whirlpool DUL300XTLQ3 Queit Partner III. The cleaning blades stopped moving-started it-waited awhile-opened it-the blades were in the same position. Took the bottom blade+filter cover off. Then I held down the metal piece on the case and switched on the micro switch on the door to see it running with the door open. The water shot straight up about 4-5" that's it. This does not seem to be enough pressure for the water to get all the way up to the top spinner. Am I looking at a new pump


If there is not enough water, the dishes would not get cleaned. Thiscould be caused by a partially closed water shut-off valve (locatedunder the sink), or a faulty dishwasher water valve (located at thebottom of the dishwasher, behind the kick panel, ... Whirlpool Dishwashers

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

The reset switch on my NS powerwasher has failed twice. the replacement i got from NS was installed by their approved service center in antiock illinois, but it failed to reset the motor. Is there a service center in NE Illinois or SE Wisconsin that can service my washer?


Hi\015\012\015\012I see you are having very bad luck with service on this washer so I'm sorry to hear that. From my knowledge of North Star they usually have fairly good customer support and it irritates me to see you are having these pro ... North Star Pressure Washers

There is a symbol of a tap when i switch the dishwasher on..and it wont wash anything? It sounds like its draining? Ive tried resetting it and switching on and off but nothing. Does it need filling up with water?


Need to check your water supply from the house to the dishwasher, it won't operate properly if the water level in the washer is low. Check the water valve at the sink ands the water valve at the dishwasher.\015\012\015\012Good Luck on yo ... Dishwashers

Indesit DI620 green light 4 keeps flasing and it wont let me switch the dishwasher one. I have tried holding the button in to reset but nothing happens also nothing happens if I switch it off and on at mains.


... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0849 seconds