Having problems with your Belling 24 in. IDW603 Built-in Dishwasher ?

The program selector is not functioning and the door will not close properly. are they related and how do i fix, tks


Answers :

Hi.

If the door does not close properly, the door switch may not close contact to timer circuit, and the machine may not do the cycle for this reason. Additionally, a short in the door switch wiring harness may jam the control module.

Before checking control module have a look at the door switch and at the wiring harness inside the door.

Regards.

Ginko.
Repair Help & Product Troubleshooting for Belling 24 in. IDW603 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The program selector is not functioning and the door will not close properly. are they related and how do i fix, tks


Hi.If the door does not close properly, the door switch may not close contact to timer circuit, and the machine may not do the cycle for this reason. Additionally, a short in the door switch wiring harness may jam the control module. ... Belling 24 in. IDW603 Built-in Dishwasher

Kenwood dishwasher kdw8st2a replaced door lock mechanism, door closing properly and program selection available but none of the program's will start. When I shut the door I just have an intermittent beeb and no error message. Any solutions?? Been trying to see if I need to reset anything but can't find a solution. Thanks jo


... Dishwashers

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Diplomat ADP8234 and the door won't close properly. It appears to be a problem with the catch. I also can't set a program but I think it might be linked to the catch problerm. Any advice


Hi, I have the same problem and when I use a screwdriver to flip the door catch to what looks like a closed position the dishwasher works fine but once finished the same problem is back until I reset the door switch again. Did you ever find a solouti ... Dishwashers

AEG Favorit 80820 dishwasher tablet door opens as soon as switched on and door closed. When you put the power on and select a wash and then close the door the small grey dishwasher tablet inside the door can be heard to open as soon as the door is closed. Normally this door remains closed until asked to opened automatically by the dishwasher at the correct point in the selected wash program.


... AEG 24 in. Favorit 80820 Free-standing Dishwasher

Smeg integrated dishwasher door does not close tite. it closes with the catch at the top and stays closed but it not flush with the rest of the doors and is angeled open a few mm or more which causes it to leek from the front bottom corner, how can I get the door to close properly ? thanks


... Smeg 24 in. DWF1 2 Free-standing Dishwasher

Door latch won't close on dishwasher. Hard to close. In addition door squeaks very loud- almost like it is catching on something. the dishwasher moves slighly when trying to close the door -it doesn't appear to be properly installed


... Jenn-Air JDB3610 Built-in Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

Beko dwi643 dishwasher door adjustment how to do it ive had a repair done to the doorsprings and the door will not close 100% how do I adjust the door to alow it to close properly


... Beko Dishwashers

Door interlock appears faulty on my whirlpool awm 321 . It wont allow program start when door closes . Needs a lot of coaxing , banging with palm of hand , knee etc .Door itself appears fine , catch looks ok , finishes and runs ok once we finaly get it started .Hve tried pressing the interlock slider in with a pencil , but cannot succeed in pushing the contacts into place and starting the program . HELP PLEASE


Only solution is to replace the interlock - it is just held in by 2 screws ... Dishwashers

Nordmende DFSN60 will not select programe,power etc ok.hold programe button and flashes P5 then 55,also EP & 188 flashes,close door and it runs through cycles but doesnt stop .when open door &


... Dishwashers

The Cascade dispenser door or lock does not close properly if it does close does not work right leaving hardened cascade caked at the bottom of dispenser inside the little door ? thanks Art 917-259-8149 I have tried to clean the hard material away but it comes back.


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

We have a matsui mf160 dishwasher. The door wont close properly as the spring that closes the door in the centre of it has snapped off please help. Can we get a part to mend it?


... Neff 24 in. S5555X0GB Built-in Dishwasher

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

My Brandt VF300 dishwasher is not draining properly. If I empty the residual water (by hand) I can still use it but the water still remains in the bottom at the end of each cycle. How can I fix this? It's driving me nuts! Also the door is not functioning properly something has broken that supports the weight of the door. It can only be shut completely or open completely! Is there a part that can be bought to fix this?


... Dishwashers

The Simpson Silencio 850 door does not shut properly and the dishwasher stops operating,but once you push hard on the door,the dishwasher starts again. There are no leaks ,but the door must have a sensor registering the correct pre-load force against the door seal , which in turn,allows the machine to operate. My machine does not work until you push hard against the closed door. What is the problem please?


... Dishwashers

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

My dishwasher door doesn't close properly. It has a panel on the outside and this seems to weigh down the door so it drops. I want to know if the door can be replaced. The model number is ACG9544 (at least I think so, some of the numbers are difficult to see! It could be ADG954 A, or ADG) Can you help?


Take the lower pannel off the bottom and look to see if you have a broken spring.you can order a new one on the sears website. ... Whirlpool Dishwashers

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program faked to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg STX2 Dishwashers

My DS603 randomly stops/pauses like if the door was pulled. The very same beeps and lights are enabled when physically pulling the door while a program is running. How can I make sure that the door state sensor (closed/open) is working properly? I have an integrated single drawer system. Thanks for your help. Ben.


... Fisher DS603W / DS603B / DS603I Dishwasher

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program failed to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

The program indicator light is on constant, but will not change programs when pressing the program selection button. And when you close the door to start the cycle nothing happens


Hi\015\012 \015\012Please check the link regarding your query…\015\012http://www.rep ... Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1100 seconds