Having problems with your Black & Decker Pressure Washers ?

Everything seems to be working but has no pressure. cratsman 1900 pressure washer


Answers :

This could only mean that the motor shaft that drives the pump is stripped take it apart and drill a small hole through shaft and drive and thread the hole and insert a screw through
Repair Help & Product Troubleshooting for Black & Decker Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Everything seems to be working but has no pressure. cratsman 1900 pressure washer


This could only mean that the motor shaft that drives the pump is stripped take it apart and drill a small hole through shaft and drive and thread the hole and insert a screw through ... Black & Decker Pressure Washers

I have a Karcher K5.86m pressure washer and the electric motor wont start. I've done the obvious like fuse in the plug etc. It was working fine one day, then got it out again and everything seems fine except the pressure pump wont start when I press the on button.


... Karcher Pressure Washers

Pressure poor After stripping the water side of machine everything seems to be in working order, I have checked all valves and orings and the central water drive. The pressure hose and bayonet orings are ok with no leeks. Everything seem to be ok but still very poor pressure.


... Pressure Washers

I have a bosch 110 plus pressure washer the problem i have is i turn on washer squeeze trigger and works fine when i release trigger and press again it wont work and trigger seems to have pressure on it


... Bosch AQUATAK 110 Pressure Washer

I have a Kracher K 4000 GS pressure washer and it seems to have been fine until today. When I start it and squeeze the trigger there is nor pressure, water comes out but as it would normally from the hose. The engine does not even seem to be under load. I used it the other day and got pressure when I picnhed off the soap hose but that did not work this time.


... Karcher G3025OH Pressure Washer

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Intermittent pressure washer engine seems to work fine, but once I engage the sprayer it cycles every second or two from full pressure to none and back, and the motor seems to rev up and down with it. K


... Karcher 2500 PSI Pressure Washer

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

I have a Karcher K3.91M pressure washer that pulsates when the trigger is released (off). It works fine when turned on, pressure seems OK. Before this started the unit would just turn off until I again wanted to use it. Is it a problem ? Correctable? All connections seem tight & I see no leakage.


... Karcher K 5.85 M Electric Pressure Washer

Karcher B402 pressure washer Motor runs as soon as power supply connected, on/off switch does not seem to make a difference and no pressure at outlet? Was working fine, stopped for half an hour, came back and wouldn't work. Thanks Bob


Bob I had this happen to my Karcher, the pressure seals have blown. $Au200 for service and replacement from karcher dealer. tyhey would not sell the parts for a DFY ... Pressure Washers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

I just bought a steam cleaner/pressure washer craftsman model 1700psi 1.3gpm and it was working fine and then just stopped spitting out water and steam. Everything seems to be working normal; it just


... Craftsman 1700 PSI, 1.3 GPM Electric Pressure Washer w/ Steam Cleaner

I have a John Deere AC2600Gh power washer and I can't get the soap to work everything else works great it just won't **** the soap up when I am pressure washing I know that it must be something simple to get it to work any help would be greatful. Thank You


Soap will only siphon into hose if there isnt any pressure in the hose attached to the wand.Remove tip from wand and see if it draws soap into hose,back pressure in wand hose will cause the spring and ball to seat/close off the inlet line for the soa ... Karcher 2500 PSI Pressure Washer

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Troy Built pressure washer starts up fine and idles nice. Start spraying and everything is fine for about 30sec to 1min then the engine just shuts off. Seems like pressure is building up and choking the engine out. If I dont spray it will idle all day long. I have cleaned the unloader area, still shuts off. I have the pump off the machine, what should I do? Model number 020208 Troy Built. Rev # 01


... Pressure Washers

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

We have installed a dishwasher (as of yesterday) and everything seems to work but it will not drain. this is a replacement for a kitchen-aid dishwasher that we have had for 17 years. Everything looks the same - it is supposed to pump through the garbage disposal. There is not an air gap but we did not have one with the old washer.


HELLO THERE PLEASE TRY THESE SOLUTIONS I HAVE PROVIDED i KNOW THERE IS NO AIR GAP BUT I HIGHLY RECOMMEND INSTALLING ONE TO HELP WITH THE DRAIN THIS WIL RELIEVE THE AIR THAT THE MACHINE PRODUCES further More \015\012\015\012 \015\012 ... Whirlpool Dishwashers

I have an electric power washer k3.99M. I just replaced the pressure hose and now the washer will not turn on. If I remove the unit from the water hose, it works, but when I hook everything back up, it doesn't.


This sounds like the hose is plugged or the nozzle itself is plugged. If the water cannot get through, the washer senses that the trigger is off and will not turn on the pressure. First just attach the hose without the gun and nozzle. If it pumps w ... Karcher Pressure Washers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Hello, I have a couple year old brigs and strattion upright pressure washer. It has always ran great untill recently. It will run for a acouple minutes before dying, like it is starving for fuel. i give it a couple of minutes, it starts right back up and again dies after a couple minutes of use... I have takin the float bowl and float off and cleand the gas tank and fuel line. everything seems to be in order. Do you have any ideas what it could be? I have not tuched the top side of the carb sinc


Check the oil level in the engine itself. Verify that your oil reservoir is full, then try again.You may also want to refer to the owners manual for other trouble shooting tips. Click this link to go to your manual.http://www. ... Briggs & Stratton Gas Pressure Washer 20244
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1060 seconds