Having problems with your Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher ?

My bosch dishwasher will not fill with water. I have manually filled it but it just pumps it out when I switch it on.


Answers :

The unit is going into drain mode. check your hose for leaks. when water leks in the base of the unit the float switch is activated and the unit will stay in drain mode until the water is removed. check float by removing side panel and look into bottom base for water.
Repair Help & Product Troubleshooting for Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

Dishwasher filling up and over flowing. switch to turn on pump comes on late or when I manually put pressure on drain. Have hard water and found much scale. could sensor/float scale cause this? Thinking about filling with white vinegar and letting sit so I don't have to take apart. Thoughts?


Take a packet of unsweetened lemonade any brand and run it through a cycle. This will clean all the scale and calcium from the pump and spray arm to improve the circulation of water in the machine. ... Asko Dishwashers

Dishwasher will not drain. drain pump works fine if you activate it manually from microswitch. I have found that the float chamber is not filling thus not activating the pump switch.


... Bosch 23 in. SHU 8805 Built-in Dishwasher

My bosch dishwasher will not fill with water. I have manually filled it but it just pumps it out when I switch it on.


The unit is going into drain mode. check your hose for leaks. when water leks in the base of the unit the float switch is activated and the unit will stay in drain mode until the water is removed. check float by removing side panel and look into bott ... Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

My Bosch dishwasher (SGV57T03GB/08) is draining and filling with water but none is being let into the main pump. I can see water going into the side reservoir but it doesnt seem to be let into the main pump area - any ideas on what is not working? Dishwasher tray is dry and float switch is not stuck.


... Bosch 24 in. SGV57T03GB Built-In Dishwasher

Indesit d41 dishwasher overfilling, pressure switch seems ok(checked with multimeter) ,when pressure switch is manually operated the electro fill valve remains open. only time fill vave shuts is when power is off or door is open. can someone please help as i cant find wiring diagram or service guide online


Possible faulty pressure switch or a faulty drain pump ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Blanco dishwasher Hi. Saw your answer on the Blanco dishwasher. We have same problem. Dishwasher makes all the pump sounds it used to, but does not start to drain at cycle start, and then no water comes in. read the manual again and think we may have been washing up - ie sinks plugged. Could this have triggered something. You mentioned something about a "micro switch" could you tell me where would this be?. We have a BFDW 650 S. Thanks, Angie


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

Model No: SE6 TIE 1 GB/17 Tecnik integrated dishwasher The dishwasher started to make a strange noise. I scooped the excess water out of the bottom and reset the machine but when switched on again it just pumps water into the bottom of the macine. I have removed and cleaned filters as per the manual troubleshooting section! Thanks for any assistance


... Tecnik Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

My GE Monogram ZBD4500 dishwasher does not drain completely at the end of the cycle. If I run a couple of manual cycles afterwards it eill eventually drain completely. Drain hose is clean, pump suction sump looks clean, drain pump impeller appears OK, discharge check valve assembly is easy to blow through in direction of drain. Do I have a sequence switch problem?


I bloody lostt you! are you still there? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Miele 24 in. G638 Plus Free-standing Dishwasher which is leaking into the pan underneath the machine (and triggering the polystyrene float switch) I am almost certain that the leak is coming from the main pump seal. Is it feasible to replace the seal (it looks like a major job to take the pump assembly apart). I guess Miele labor charges would make the repair not worthwhile Is there a service manual for this machine. I guess I would need it


Hi\015\012\015\012Please check the bellow link to have a detailed view regarding your query…..\015\012http://www.appliance-r ... Miele 24 in. G638 Plus Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2150 seconds