Having problems with your Bosch 18 in. SRS56L08 Logixx Slim-Line Built-in Dishwasher ?

Water flow cut in and out

\015 When you switch on the unit drains for a while then you hear the water coming into the machine but the "check water " light lights up and the water keeps cutting out then coming back on but the wash cycle never starts.\015

Answers :

Repair Help & Product Troubleshooting for Bosch 18 in. SRS56L08 Logixx Slim-Line Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

I have an Electrolux dishwasher model ESF489, and I can't get water to go into it.the water goes as far as the machine then the inlet hose just pressurises up.I know the hose is clear .The machine tries to go through its cycles but because the water will not flow,it just cuts out after a few seconds.????


Assuming the control card is working ok, the most likely problem is the water inlet valve which may have a faulty solenoid. Do you not get any indication of beep or fault lights on the dishwasher.\015\012You can find a possible replacement at ... Electrolux Dishwashers

Kenmore elite dishwasher model 665.13153k701 At end of wash cycle, water does not drain completely. Intemediate drains during wash do drain completely. rinse and hold drains completely. watching water at end of wash thru disposal, water flow cuts off like valve closed. other drains taper off


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a bosch SHV43A03GB dishwasher. It has a problem when it cut out water flow in. the guy who repairs it seem s only to have to push a button or switch under the machine to get it to work again, cant find switch/ button- please help!


Programmer not working ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Errratic flow,bursts of water


... Pressure Washers

GE PDW8280 - MIDDLE ARM WILL NOT SPIN - WATER FLOWS AND SPINS FROM TOP AND BOTTOM ARMS - MIDDLE ARM HAS WATER FLOWING BUT WILL NOT SPIN. tOOK APART AND CLEANED - SPINS FREELY BY HAND BUT NOT DURING CYCLE. SUSPECT LOW WATER LEVEL? WATER IS ONLY UP TO BOTTOM OF HEATING ELEMENT


Take the whole middle spray arm assembly off -- spray arm and long tube that it is attached to. I cleaned the inside of the spray arm and found some odd stuff but it still didn't swing after the cleaning. I order all new parts and when I was repl ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Whirlpool model GU1200XTLS3 - water doesn't flow in properly unless i put in a pitcher or 2 of water. In the initial sensing/fill process and during rinse, i have to pour in pitchers of water, then water flows in as it should.


Possible that the inlet valve , the level sensors are faulty, Most likely that the water level sensors are not reacting and cutting off the inlet valve unless the water level pressure comes in with the addition of the water ... Whirlpool Dishwashers

AEG OKO Favorit 4020 no water flowing into spreaders to wash. Water flows out the side outlet and the element heats up but no water?


... Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

Water not flowing into dishwasher. I've taken door off, detached 1 lead to the solinoid. It shows 987 ohms resistance, can feel AC hum when 110v put into the coil - but no water flows (water attached). Where do I go from here?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your post and the findings of the valve resistance of 987ohms, ( normal is 1Kohms ) it sounds well within acceptable range, however the valve can sti ... Bosch 24 in. SMU70 Built-in Dishwasher

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

It seems to turn on but no water flows in I can here the motor running but no water flows the water has not been shut off


There are two possible reasons for the situation as you describe it:\015\0121. Water-inlet valve \015\012\015\012The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually ... Dishwashers

Hello! My GE Dishwasher (Model # GSD2000G00WW) will not fill. The water supply is flowing properly after cleaning out some lime and mineral deposits, but no water is going into the machine. If the water flow valve needs to be replaced (?), is there a local distributor in the Cincinnati/Blue Ash area in Ohio (zip code is 45242)? Thanks! Steve Brodbeck


I need to know is the water not going in the machine at all in other words when you switch on the machine with the tap open can you hear the water flowing,if you can here the water flowing check the hight of you drain hose if it is too low down you w ... Dishwashers

Does not give a continous high pressure flow cuts in and out


Hi. Water flow may be restricted to the pressure washer. Check that all hoses are free of kinks, leaks, or blockage. Make certain all hoses and fittings are connected properly. Make sure to open the faucet/spigot ... Karcher K2.26 Electric Power Washer

The water flow is not normal. Very little water is flowing thru the machine


Hello,Welcome to FixYa.With the symptom you`ve described..."The water flow is not normal. Very little water is flowing thru the machine", ... Kenmore 24 in. 16039 Built-in Dishwasher

At beginning of waswch cycle, water flows in. Then it stops and the cycle doesn't continue even though the countdown timer continues. Water flows out freely.


When the water comes in to dishwasher the wash pump should start if you hear a hummimg sound it means that the wash pump is either blocked or the capasitor on the pump is faulty or maybe the pump it self needs to be replaced ... Dishwashers

No water flow to dishwasher disconect the plug at flowing switch 120V no power at water valve plug


Check to ensure you have proper volatage at the connection box behind the toe kick\015\012 the you will need to open the door to check the door switch for both voltage and continuity ... GE 24 in. Profile PDW7800 Built-in Dishwasher

No water flowing to dishwasher, I check the power to flow switch plug 120v no power to water valve


Check to make sure both sides of your door switch is closed as well\015\012 if your door switch is not closing properly it will not send voltage to the water vale ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Siemens dishwasher help i have a siemens dishwasher with no manuals and on my fresh water pipe there is a box which has a electric sign on it this also has another arrow on it is this a flow arrow? my copper pipe has my outlet on the top should my outlet be underneath to suit this arrow and the water is flowing down and not up the pipe thanks ****.


My siemense dishwasher (2 month old) stopped working\015\012No matter which program I choose, after 1 min the program stops and I get "tap" symbol on the led display. \015\012Instructions says it might be a problem with the water source b ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0753 seconds