Having problems with your Bosch 23 in. SHU3302UC Built-in Dishwasher ?

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons. Usually, these issues are related to\015\012kinked hoses, knocked out disposer unit (if connected with the dishwasher drain\015\012hose) & clogged drain pump & filter. Also note that dishwashers do not\015\012drain completely after a finished cycle and this is normal. Dishwashers are\015\012designed to leave some water in the unit to ensure that the heating element\015\012doesn’t overheat. If you suddenly begin to experience a large amount of water\015\012being retained in your dishwasher, you have a problem. Some of the most common\015\012reasons include that the drain hose isn’t working properly, the drain pump\015\012isn’t working correctly, or possibly there is a plumbing problem in your home’s\015\012drain lines.
\015\012
\015\012

\015\012\015\012First\015\012check whether the drain is not clogged or blocked and the line is not kinked.\015\012Check all the hoses for blockages & also clean the air gap. Has the\015\012disposer been replaced recently? If so, chances are the knockout is still in place.\015\012Simply remove the drain hose from the disposer, and knock out the plug. If the\015\012disposer has not been replaced, try removing the drain hose from the disposer\015\012and use a wet-dry vacuum (prepared for water, of course) to **** any water (and\015\012hopefully anything else) from the drain line. Then reconnect the hose, and test\015\012the unit. If you have checked the air gap and the drain hose and can’t locate\015\012the problem, then it is an issue with the drain pump of the dishwasher.
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do\015\012accept the solution if the issue is resolved or else revert for further\015\012assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Bosch 23 in. SHU3302UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Bosch 9925 - water comes in and drains - but not enough pressure to make water comes out of rotating arm more than about 6 inches. Do I need a new pump? I cleaned all holes and filters. How do i access the pump - through the inside of the machine? Thanks. LDS


DO YOU HAVE AN ISSUE WITH HARD WATER IF SO TAKE 1 GALLON OF VINEGAR START MACHINE LET MACHINE DRAIN THEN WHEN IT STOPS DRAINING OPEN DOOR AND FILL WITH VINEGAR THIS WILL PUT ADIQUATE AMOUNT OF LIQUID IN MACHINE TO RUNDON262-893-4840 ... Bosch Dishwashers

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. I have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle. HELP!


Here it is - Maytag Quiet Series 300 Manual ... Maytag Dishwashers

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

GE TRITON XL NOT DRAINING-CHECKED AIR GAP AND HOSE TO DISPOSER. USED BASTER TO REMOVE LOTS OF WATER THAT SMELLED REALLY BAD ON ONE RINSE LIKE BACKING UP. CLEANED SCREEN AND AREA IN PUMP AFTER REMOVING IMPELLER (SP). WATER NOT EVEN COMING UP THROUGH DISPOSER. BAD PUMP?


... GE Tritonr XL GSD6260JCC Dishwasher

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

Miele dishwasher G818scv1plus intake/drain light comes on. i cleaned the drain line ,cleaned the tripple filter in the cabinet, checked the pump it moves freely, cleaned the water inlet filter.


... Miele Dishwashers

Ariston L64 dishwasher will not drain/ pump out waste water. Dishwasher comes up with fault lights to say drain blocked, but I have wet vac the drain and is all clean.


If you are attaching the drain hose to a new garbage disposer or a\015\012disposer that has never had a drain hose attached it could be that the\015\012“knock-out” plug on the disposer hasn’t been removed. You can check for\015\012t ... Dishwashers

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

Havnt used my dishwasher in 2 years on account of saving water. now when i push the start button some water flow into machine for a few minutes and then just stops. manual says to clean filters and drain pump but all clear. what is next plan of action?


Try pouring water from a bucket through the front. maintain the level. It should not overflow.Run a empty cycle. If there is a air block it will get cleared. ... Asko 24 in. D3120 Dishwasher

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Pump problems mine is the 14w. all that happens when i turn it on is the pump tries to drain the water, but there is no water to drain as the cycle has not started. all you can hear is the pump sucking water. no water comes into the washer either. somebody please save me.......


... Zanussi 18 in. DCS12W Free-standing Dishwasher

Bad smell This is more of a general question. When I run the dishwasher there is a bad smell as it fills with water. It comes out of the sink/garbage disposal. I have cleaned out the line that comes from the garbage disposal to the drain and that doesn't stop the smell. Is there a line that needs to be cleaned from the dishwasher to the sink or how can I fix this issue? My dishwasher, at the drain, has water standing and it smells. I think it is there from condensation as the dishwasher, unknow


Smell is not the fault of the dishwasher but your waste disposal unit - they stink!it may be awkward, but arrange your drain so that there is a water barrier. better still. install a standpipe for the drain, again with a water barrier ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Dishwasher - The dishes and glasses do not come out clean. There is approx 2 inches of soapy/dirty water that remains at the bottom of the dishwasher. I was told by the sales people that this was normal in order to keep the ... moist. I have since leared that this is not normal. The washer was purchased approx 1 1/2 years ago and was installed last January. Problem has always existed. I have replaced the Drain Pump because when I spoke to someone at GE that was thought to be the problem. NO


Your problem is to removed the clogged into the drain.. I'll post back again and post here the steps to removed the clog..Thanks ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1687 seconds