Having problems with your Bosch 23 in. SHU3302UC Built-in Dishwasher ?

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


Answers :

There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found out by accident of the recall...we were never notified, even though we registered our Bosch SHU33UC unit when we bought it...poor customer service!
Repair Help & Product Troubleshooting for Bosch 23 in. SHU3302UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found o ... Bosch 23 in. SHU3302UC Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be. Thank you TD


WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us k ... Whirlpool Dishwashers

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be


See this step: ... Whirlpool Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

After selecting wash cycle,I push start button. washing light comes on for a second then goes off.start light keeps on blinking. washing cycle would not start.


Check flood switch float is on(the float under the bottom rack)...also the switch under that...also you ca use a 110 volt test cord to test the inlet valve ... Dishwashers

The "Normal" button light keeps flashing. The door had come open during a wash cycle and there is still water in the bottom of the dishwasher. I've shut off the power, but the light still blinks. Model is KUDSO1FLSS6


The washer had been interrupted during the program cycle and so the main micro controller has hung up. You can remove off plug for few hours or iover night to reset the processor.\015\012Now make sure that the door latch is clicking and contact ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Had problem with clean bilking light. I was able to reset with your help. But it keeps coming back after every cycle. Dishes are not drying as well. How can I fix this?


The flashing light indicates there is a heater issue caused by a failure of one or more of the following: (1) The heater. (2) Door switch. (3) Water high temperature limit switch. (4) Electronic control heater relay. (5) heater wire may have loosened ... Whirlpool Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

The normal cycle light on our KitchenAid KUDS01IL dishwasher is blinking and no other cycles or options can be selected. I have cycled the power to the unit multiple time and it keeps blinking. What is wrong?


... KitchenAid Dishwashers

My dishwasher keeps filling with water and the water then starts to come out of the bottom of the door. It therefore does not go into any cycle but keeps trying to fill with water but the water keeps coming out of the bottom of the dorr from the inside


... KitchenAid KUDS24SE Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

I have a whirlpool du1100xtps sudenly stop working when I plug the machine, the stop/drain button comes on, and about 15 seconds later turns off and the normal button comes on but blinking and after about 15 seconds the stop/drain buttom comes on too also blinking and then just keeps going on like that and nothing else happens??????? how can I fix it, or what is wrong with the machine?


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Thank you Daniel Scott. The solution you posted worked for me and saved me calling a technician. My clean light was flashing and I followed your solution to press Heat Dry - Normal twice. And it worked! Thanks so much! ... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

Dishwasher is less than a year old. Once in a while it will stop about 10 minutes into the cycle, then the display lights will blink. Sometimes it will stop and the lights wont blink so we will come back later thinking it is done only to open it up and there is water sitting in the bottom. Doesnt happen all the time but sometimes and yesterday happened about 10 times finally gave up. I can cancel and restart the cycle but the same thing happens.


I would most likely guess a faulty latch....it will cancel the cycle, thinking that the door has opened, and the lights will flash. After a certain amount of time, it might "time out" and reset and the lights would stop flashing. Unfortunately it's ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


I had the same problem and was told to unplug the dishwasher, wait, and then plug it back in. That didn't work; but I decided to try again. So I unplugged the dishwasher, wiggled the heating element in the bottom, made sure it was in the right positi ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Close the door and to cancel that just press hi temp and hetaer dry again hi temp and heater dry and all the lights is gonna light up, it getting into test mode.\015\012After that press cancel \015\012Now get somebody to replace the therm ... Kenmore 24 in. 17032 Built-in Dishwasher

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Clean light keeps blinking and I can't start a new cycle


That is a comon problem with that model. It is not sensing a temperature change in the water. Push i believe it is heated dry and sani rinse going back and fourth between the two to clear the code and see if you can get it to complete a c ... Kenmore 24 in. 15932 Built-in Dishwasher

Cannot start a cycle. The "Steam Clean" button keeps blinking.


... Jenn-Air JDB3200AWS Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1127 seconds