Having problems with your Bosch 23 in. SHU3307UC Built-in Dishwasher ?

It stopped running and has a smoke smell. It will not drain or do anything.


Answers :

Hello,

Welcome to FixYa.




Based on your post "It stopped running and has a smoke smell. It will not drain or do anything." it may just be a loose/burnt connection in the dishwasher junction box or a severed wire in the door panel.

** I would start by first shutting off the breaker...safety first**

Then removing the kick plate ( access panel at the bottom )...

macmarkus_133.jpg

...and checking the wiring at the junction box for the dishwasher 120vac supply line.

Remove the murret's and visually inspect the wire for "resistance burn" and strip the wires back and install new fastener's if necessary to repair.

i.e.

60f6a31.jpg

This is actually quite common to find a wire connector come loose due to improper fastening and once the unit is in use for a while the connections heat & cool, become loose from normal operating vibrations and burn up from all the added heat caused by "resistance".

Typically this will manifest in just the manner you've described.

If it looks OK there I'd remove the outer door panel ( careful the edges are sharp ) via the six #20 torx head screws...

macmarkus_168.jpg


...check for a severed wire at the pivot point in the door, typically covered in a plastic casing as shown here..
.

macmarkus_169.jpg

The small plastic blocks which may be present in the bottom corners of the door panel, i.e.

macmarkus_170.jpg
...they can be a pain to re-install, but they do only go in one way, however it is ok to leave them out...their only purpose is to strengthen the structure.

Let me know what you find and I'll try to assist you further if necessary. Thank you for choosing FixYa today for your inquiry.


Regards,

Macmarkus :)

Repair Help & Product Troubleshooting for Bosch 23 in. SHU3307UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It stopped running and has a smoke smell. It will not drain or do anything.


Hello, ... Bosch 23 in. SHU3307UC Built-in Dishwasher

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo


... Dishwashers

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Miele G 870 SC dishwasher had blocked drainage due to stopped up sewer which got snaked out by plumber. Ever since, the drain pump won't stop running. Have cleared the trap, filter, and drain-filter and still the pump runs continuously.


Hi\015\012\015\012The problem is with the float switch mechanism located at\015\012the bottom of the unit...either this has gone bad and should be replaced or the\015\012pump itself is bad & should be checked. Hope this helps...please pos ... Miele 24 in. G870 Built-in Dishwasher

My garbage disposal had something stuck in it. i did not know and the sink was backed up. i started the dishwasher and it sounded like the motor was running like a drain emptying...i thought it would stop but continued. i unplugged the dishwasher, freed the garbage disposal and the drain is now clear. i turned on the dishwasher and the sound is the same. the large POT light is lit up and when you try to shut it off it doesnt stop running. i unplugged it for fear of breaking something. HEL


Hello,Welcome to FixYa.Based on your post, the ... Asko D3251HDSS Stainless Steel Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Dishwasher stops running and won't drain


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain out ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

Smeg Dwi409c dishwasher is stopping 3 minutes into cycle with no fault lights or anything, I hear it fill with water but then stops, but I do notice the water is not draining which I assume is why it is stopping, correct me if I am wrong. Have removed the filter but still not draining. Any ideas?


... Smeg Repair Pcb / Module Dwi409c

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Kudlo2frss3. Dishwasher runs, stops, starts blinking and wont drain. Cleaned it out. might run 1 cycle then the next it shuts off and is not draining.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Calypso washer display "FD" perhaps meand full drain and can't reset and just stop. I run washer with back cover out to see that while water doesn't fill up the drum but normally agitates and just fill up the water reservoir to full and don't drain out to sewer and washer just stops with the message "FD"


Peace broohilda,ngafm At your service!With an error code the only way to find and to repair this is,First unplug the washer and wait a few minutes then restart it like rebooting your computer when its acting strange! ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have a MDB4630AWS1 series dishwasher that is only a couple of weeks old. Suddenly, it now starts the wash cycle but then the Cancel/Drain light turns red, and it drains and stops the cycle. Check for items blocking the sprayers and looked for anything clogging the interior. It does this with all the settings. Seems to work for a few minutes, but then it just drains and stops. Any help would be greatly appreciated.


... Maytag MDB4630AWS Dishwasher

My kitchenaid kuds24se won't run or drain (it filled and stopped). If I remove the drain hose to clear it while the tub is full of water, will the water run out all over the floor?


... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

DIshwasher stopped during wash and won't run or drain.


Sounds like a drain motor startup capacitor, or stuck pump. Try disconnecting power and turn the water pump manually. Some disassembly required. Then after a few good hand spins replug and try again. ... Kenmore 24 in. 17022 Built-in Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Drain pump makes draining noise but does not drain water from the wasmachine. It drains water correctly when we use the switch for drain or when we use the switch for spinning. The pump does not stop running. What is wrong?


You will find this link useful. also read commentts and replies following it.\015\012http://www.squidoo.com/Bosch_Dishwasher_Drainage_Prob ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1339 seconds