Having problems with your Bosch 23 in. SHU33A Built-In Dishwasher ?

Continuious Filling. The supply line continues to fill the unit at a slow rate even when the unit is off.


Answers :

Seems like the inlet solenoid valve is stuck in the partly open position. This happens when tiny particles become entrapped inside the valve even though manufacturers attempt to prevent this by installing a screen at the water connection. So one possible solution is to remove the valve and thoroughly clean it. I do this by actually disassembling the valve body. Usually it is a split-shell assembly with a rubber gasket at the split line. Just be careful and if you tear the gasket, it can be replaced with automotive silicone gasket maker (comes in a tube). Draw pictures of each step if you need reference for re-assembly.
Repair Help & Product Troubleshooting for Bosch 23 in. SHU33A Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Continuious Filling. The supply line continues to fill the unit at a slow rate even when the unit is off.


Seems like the inlet solenoid valve is stuck in the partly open position. This happens when tiny particles become entrapped inside the valve even though manufacturers attempt to prevent this by installing a screen at the water connection. So one poss ... Bosch 23 in. SHU33A Built-In Dishwasher

Maytag Dishwasher I would like to know the proper water level after DW fills. Older Whirlpool units a quick guide was when water just covered heater. I have a new D/W and the water supply is difficult to access, there is a kink in the water line slowing the water flow. The D/W fills to bottom of heater, but because the unit is so quiet I can't determine if it is timing out or working properly. I intend to repair water line when counter work is done. Thanks for any help Gary


Newer Maytags should fill close or up to the heater not over. Sounds like your alright for now but I would get that water line fixed. ... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

My plumber just installed a new water supply line for my dishwasher. Now the pump comes on but no water fills up in the machine. If I fill the bottom of the unit with water, it works just fine. Even though the water supply is ON, it does not pump water into the 'box'. Thanks, Art


You don't know how many times I've heard and found the shutoff valve off or partly turned off. Water entering DW is from line pressure not pumping. Items to suspect (again) the water supply valve (would'nt be the first time a new valve is bad). The ... Whirlpool 24 in. DU915QW Built-in Dishwasher

Bosch SHX46A02UC-21 Won't Fill and Drain Runs Continually. Original presentation of problem was that it wouldn't drain. Discovered that Garbage Disposal had plugged drain line. After clearing Drain Line, now drains fine but the drain pump runs continuously and it never fills with water. Have done the Cancel, Power Off routine however, even after that, drain pump runs continually.


Float switch is in the flood position and the drain pump is running..\015\012there is water under the dishwasher or that switch is stuck up.. ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My Bosch SHX46A02UC-23 dishwasher is continually letting in water from water supply, even when unit is turned off.


Hello,Welcome to FixYa.Based on ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

GU2700 Whirlpool - Does NOT FILL 2 Gallons on INITAL FILL - unit has new parts FILL VALVE IS NEW OVER FILL SWITCH IS NEW while filling if you reach under the unit and push the over fill float up it turns off the fill cycle - if you let go - unit keeps filling - but does not add the correct 2 gallons - water is not even close to the heating element - does not have enough water to come out of the TOP SPRAY Arm


... Whirlpool Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

Whats the secret to getting the chopper unit back into the unit. There Tip was to use a small wrench or pair of pliers to compress the spring and align the unit. However , even with it fully compressed , the angle is right and it dosen't want to line up . I know to get it off, they advised to pull up. So it must be the opposite to replace it. I've been trying!!


Its spring loaded,so take a small tool and hold back as you insert back into mount.God bless,tom ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

I have a Kenmore Elite dishwasher (2004) and recently it has been leaking internally at a very slow pace. When not in use it will slowly fill until the floor of the unit is filled and then leak onto the kitchen floor unless we press the drain button and then it drains completely. The water seems to be coming from the front of the washer, potentially from the door itself. The amount of leakage is barely discernible but will fill over the course of a 24 hour period. The dishwasher otherwise wo


Hello,\015\012The water is admitted into the dishwasher through a little magnetically controlled valve underneath your dishwasher. This valve opens and shuts electrically. There is a little plunger in it that is pushed shut by a spring when no ... Kenmore Dishwashers

I have a bosch SHE58C dishwasher. The cycles all work, it fills so the water line is ok, it washes, and it drains so it is not clogged. I cleaned out the sump and it is all clear. However, I think the "brain" or control module is bad. When I try to run a cycle, it does not fill. One other note is that it continues to run when the door is open. Is there a way to reset the "brain"? I've tried killing the circuit breaker


I have a similar problem with my SHE55M15UC model. I bought it last week and I had to push and hold the cancel button before it would start another cycle. If it doesn't finish the previous cycle, it will not let water in. Also, mine doesn't shutoff ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a model SHE 44 C05 UC/40. It is three years old. It starts up fine, fills with water and goes into the wash cycle. Then it continues to wash indefinitely, even though the electronic timer display counts down to 1 and sets there. It still continues washing until you turn it off with the power button


... Bosch Dishwashers

I have a pot scrubber 600. I just replaced the water line. I had to disconnect the electric wire to service the unit. Everything is running except the water doesn't fill, and there is an awful buzz from the actuator for the water discharge. What is going on? The water valve is on but doesn't fill.


So tell...me...you replaced the water line why......its probably moot as to why you did it....just realize that the large majority of no water problems are due to a wire off or loose on a water solenoid valve or a bad solenoid....I am going to provid ... GE Dishwashers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

Dishlex dishwasher global 300. Dishwasher continues to drain with ECO light flashing. Service manual says it is due to an incorrect fill level or fill line.


Some diswashers have a sump in the bottom with a float switch. If the water level overflows the float will activate the switch which will kill the machine and run the drain pump continuously. ... Dishwashers

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1164 seconds