Having problems with your Bosch 23 in. SHU 8805 Built-in Dishwasher ?

Bosch shu9905 the wife **ticed water level was **t emptying...thought i left dishwasher on ...so continued and then ** water was coming out and burn smell ..did a test and the scrub wash lite = water filling fault (over or under filling)


Answers :

Check the drain pump. First, manually initiate drain by pressing the second and fourth buttons on the keypad at the same time. If it pumps out, disregard the rest. If it doesn't at least hum, check for power at the motor.
\015\012Remove lower rack, lower spray arm, and screens in bottom, remove all water inside. Check for debris under pump cover in bottom of sump. The drain pump suction is through the hole on the left.
\015\012Behind the toe panel on the left is the drain motor, If no debris was found inside, the drain pump may have failed. Remove outer door panel (you may need to remove the two screws on the sides of the control panel.) Remove the metal panel across the top of the motor area , disconnect hose in front of pump, disconnect wires to pump, press tab at top of pump and rotate clockwise to remove pump. The impeller could be loose on the motor shaft, or the motor windings failed.
Repair Help & Product Troubleshooting for Bosch 23 in. SHU 8805 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch shu9905 the wife **ticed water level was **t emptying...thought i left dishwasher on ...so continued and then ** water was coming out and burn smell ..did a test and the scrub wash lite = water filling fault (over or under filling)


Check the drain pump. First, manually initiate drain by pressing the second and fourth buttons on the keypad at the same time. If it pumps out, disregard the rest. If it doesn't at least hum, check for power at the motor.\015\012Remove lower ra ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have run the test cycle and the quick wash and pre-rinse lights are illuminated. Does this mean a water sensor and filling fault?


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

It is not pumping water into the spray arm to wash the dishes. I can get it to fill with water and drain the water, but when it fills and the cycle timer starts, nothing happens, and a slight burning smell occurs. Does this model have a reversable pump or a direct drive? I am thinking this is where i need to start.


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

Previous wash cycle worked perfectly. Next morning , dished not washed. Water pressure is insufficient to spray. Checked sprayers and clean. Removed bottom sprayer arm and tested. Water flows barely. Water fills but pressure insufficient to spray. Actually 'bursts' slightly on shutoff. All other functions work perfectly.


... Kenmore 16872 Built-in Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but it "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning. I have tried changing the programs from Pots and Pans to regular wash but the same results. Nothing happens


... Asko D1776 Stainless Steel Built-in Dishwasher

My Bosch Dishwasher will not fill with water, it is a model SHE43F02UC/48. Follow ing the diagnostic instructions, caused the following: Cycle count-PO,Quick wash continuious light, Rinse Hold-flash. after pressing power scrub and regular wash agin; count down-off, regular wash off amd a quick wash-flash


Hi\015\012 \015\012 \015\012When the Dishwasher is not filling in, you'll need to check for the water inlet valve, the filter screen and the float switch/assembly. Also check for the float asse ... Dishwashers

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found o ... Bosch 23 in. SHU3302UC Built-in Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but the "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning.


... Asko D1776 Stainless Steel Built-in Dishwasher

Dishwasher Westinghouse SB915 fills with water for wash cycle but does not wash.


... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Model #EIDW6105GS1 ELECTROLUX DW- Fills with water then drains immediately. no wash cycle no rinse no nothing. AND ALL lite on the control panel are blinking. Any ideas? Please advise.


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I was trying to wash dishes and i noticed that the motor wasn't running but water was filling up the unit. I smelled something burning, and i shut it off and took off the cover and i felt the motor and it was very hot to touch. I assume the motor is frozen. How do I change the motor? Is my diagnostic accurate?


Hi.From your description it sounds like the pump motor has blown and must be replaced.Before replacement the motor can be tested by jumping eac of its wires to energize it directly, for safety reasons the operation must be done by a ... Dishwashers

My ADG7540 fills with water then stops. sometimes the wash pump will run for a second but stops. I've tested the pump and capacitor, any ideas? Adrian


Check the water level sensor and control panel to make sure they are all syncing and getting power. ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

No heat washing cycle completes normaly, exept no hot water or drying.i tested heater for resistance and seems ok,is there a fault with control pcb or is there a faulty sensor that im not aware off? can you make any suggestions? thanks steve


You should check for 115/220v on heater tags,\015\012In case you don't have it, your problem is a malfunction thermostat that should be replaced.\015\012\015\012Good luck! ... Zanussi 24 in. ZSF6120 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1958 seconds