Having problems with your Bosch 23 in. SHU 8805 Built-in Dishwasher ?

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


Answers :

The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full
Repair Help & Product Troubleshooting for Bosch 23 in. SHU 8805 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Hobart ar14 i think the retainer _switch weldment is shot .how do iknow ?the machine doesnt torn on when i close the door. it also looks like its burnt .


Do you mean the door switch/magnet? ... Hobart AM14-253 Free-standing Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

I purchased a new dishwasher on 2/22/07 at the Home Depot in Parksburg,Pa. I first had to have it repaired on 4/28/08 for wires stuck to inner door. They repaired two broken wires and added insulation so wires do not stick to the door. The second repair was a little more than two months later. On 7/18/08 they had to install a new motor because the motor locked up. Both times I waited several weeks due to not having money and appliance center being busy. I used J.B Zimmerman in Blue Ball,P


Hel1Dav2,\015\012\015\012I understand your frustration with having to deal with major repairs to a new applaince. However, I don't belive this is the correct forum that you need to use. I have found a helpful link that you may try in th ... Dishwashers

I'm attempting to reuse a Maytag dishwasher motor for a bench grinder. Since this is a reversible motor, I'm not sure how to connect the wiring to a simple switch so that it works in one direction only. The motor has 4 wires: blue, gray, red, yellow. Not sure which to connect to the hot (black), return (white) and ground (bare) wires from the romex and can't find a wiring diagram online for this dishwasher. Any ideas? Thanks.


... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Bosch she4am Diagnostic program indicates door switch error. Troubleshot the magnetic hall effect style switch, it reads 8vdc or so with door open and almost 12v with it closed. Can't find any information in this style door switch,,,thoughts?


... Dishwashers

DISHWASHER I have a problem with my CDA - CW494 dishwasher (6 ½ years old) You can switch it on and the lights come on. Then when you go to shut the door the lights switch off and the dishwasher doesn't start. If you move the door up and down the lights switch on and off. My husband has checked all wiring connections and they seem fine.


One of the switches in the door latch are not making contact properly. before you take the door apart make sure the dishwasher is 100% level. this can affect the door lat switches ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool Dishwasher detergent door not operating properly. Main wash door opens immediately after starting dishwasher. No pre wash cycle. Loud humming noise coming from bi-metal switch or wax motor attached to the detergent cup assembly. I just replaced detergent cup assembly including the wax motor and I still get a loud vibrating humm from the actuator. model number du1055xtp3


Pdemaio,ngafm at your serviceI believe the loud humming you describe is an electronic problem. And is not worth changing parts randomly and spending unnecessary funds in this fashion!my advice is a hands on experi ... Whirlpool Dishwashers

My Hotpoit FDL570g dishwasher (that is less than 2 years old) is tripping the circuit breaker originally during a wash and now when the unit is switched off and and door is closed. I thought it may be a door lock / microswitch problem and replaced the microswitch. The dishwasher was good for four seperate washes but now the problem has come back when crockery is loaded when the machine is switched off. I'm going to check for bare / rubbed leads but not expecting to find this with a dishwasher of


Hi,\015\012\015\012If your washer is tripping the breaker when it is switched off, this is often a sign that water has leaked - or is leaking - into the bottom of the washer under the washing compartment where there are lots of exposed el ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Whirlpool DUL300XTLQ3 Queit Partner III. The cleaning blades stopped moving-started it-waited awhile-opened it-the blades were in the same position. Took the bottom blade+filter cover off. Then I held down the metal piece on the case and switched on the micro switch on the door to see it running with the door open. The water shot straight up about 4-5" that's it. This does not seem to be enough pressure for the water to get all the way up to the top spinner. Am I looking at a new pump


If there is not enough water, the dishes would not get cleaned. Thiscould be caused by a partially closed water shut-off valve (locatedunder the sink), or a faulty dishwasher water valve (located at thebottom of the dishwasher, behind the kick panel, ... Whirlpool Dishwashers

Hello I recentley repaired a broken door latch on chef electronic diswasher the push button type not the rotary switch style. i had to disconnect the circuit board I wrote down the were the wires connected i have discovered that when I reconnected everything i had not got all the wires in the right place is there any way I can get a wiring diagram so I can connect the wires correctly thank you


Unfortunately as i know it is difficult to find a wiring diagram. Better try an authorized service station where they may have similar appliances. ... Dishwashers

Jdb2100aws dishwasher - door handle fasteners loose, handle ready to drop off. This is a dissambly question: The middle section of the door has an upper one-third (which contains the input switch strip) and a lower two-thirds; the upper section must be removed to tighten the door handle fasteners. After wiring is disconnected (yes, power is OFF), the upper section appears to be held to the shell by some kind of barbed fastened from the inside, run through a tab on the door shell and into a fema


After removing the stainless cover l tried to disassemble the door further but found it difficult, there is a hard thick plastic cover, i took my dremel and cut a small hole large enough for a wrench to fit and tighten the thin nut on the handle, lin ... Jenn-Air 24 in. JDB2100AWS Built-in Dishwasher

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

GE Dishwasher - front door assembly - GSD5420G00WW - Took the front door apart to check the wiring as d/w was acting erractically (not draining fully, not obeying pushbutton commands every time). Everything seem OK, but now not sure how the detergent latch lever and the sequence switch lever fit together to reassemble the door. Help, please. Rick


... GE Dishwashers

Indesit d41 dishwasher overfilling, pressure switch seems ok(checked with multimeter) ,when pressure switch is manually operated the electro fill valve remains open. only time fill vave shuts is when power is off or door is open. can someone please help as i cant find wiring diagram or service guide online


Possible faulty pressure switch or a faulty drain pump ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have a Neff S544X2gb/17 dishwasher which seems to be dead i.e no programme lights on. Have checked fuse in plug, dishwasher on/off switch which has live going to it and out, interferance filter is ok as is wiring harness in door panel. When you first switch on, for a split second you can hear a noise coming from the aquastop valve. Any ideas?


... Neff Dishwashers

Hobart Dishwasher We have an old smaller built-in dishwasher at our church (Hobart model WM5H). It doesn't stop spraying water if you open the door to remove a rack of dishes to put the next rack in like it is supposed to. One member thought it may be the Electrical Timer Switch? Would this be a fairly easy repair?


I guess I didn't understand your statement of the problem. If you know that the washer has gone through an entire cycle, and it is time to take out the RINSED dishes, yet the washer turns on when you do this, play with the door interlock and the doo ... Hobart Dishwashers

MY MAYTAG dishWASHER suddenly will not go through both cycles so the dishes do not get clean It is an older one that has the cutting board top. Not built in. Anyone out there. I thought if I take the door off I can look at the cycle switch. the model number is LWC300 and Series 01 Thanks a bunch


Dishwashers normally stop(thermostop)to wait for water to heat thus maybe the element is fault,try getting a good ohm reading from element,like 20 ohms,hope this helps ... Dishwashers

We have the same problem. At first, we were getting a horrible detergent film on everything. We thought that was because the detergent cup wasn't opening or the water was too hard or not hot enough. We kicked up the rinse agent as high as possible, switched to a liquid detergent, and only placed shorter items towards the door. The cup still wouldn't open consistently and our dishes still needed to be re-cleaned. We stopped closing the cup. No change. Why would liquid detergent leave a powder fil


You dont need a new dishwasher. it is your water that is causing the film and residue. go to www.dishwasherfilter.com. they have an awesome product that is affordable and g ... Dishwashers

I,ve got a prima LPR450 and it won't switch on, i've checked the obvious things like the fuse, circuit breaker and wires in the plug and they ere all fine. when i push the power button there is a faint clicking sound from inside the door.


... Dishwashers

No Heat Had the blinking clean light problem, reset, and it fills and runs, but element not heating. Element reads 10.6 ohms, both door switches seem to be making. What else might be causing it not to heat? Is it possible to find a wiring diagram or schematic?


Should be a tech sheet stuck to inside of the bottom toe panel.Switches may check OK with no load applied. There is also an over temperature thermostat that may be open. If all checks OK, control may have failed. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1335 seconds