Having problems with your Bosch 24 in. SGS09L02 Logixx Built-in Dishwasher ?

Bosch SGS09A02 Logixx no Hot Water and not completing Cycle.

\015 When running a cycle near the end the display says 1 min left to go, after a few minutes or so the display moves to\015\012more minutes(30 minutes for example). It\015\012then changes from 1 min left and some other random figure continuously. This continues and the cycle never ends. I eventually have to open the door where the spray arms seem to be working but\015\012I can see the floor full of foam. The water seems cold, I have not felt the\015\012water hot over the last few attempts opening the door at the begin middle and\015\012end of cycles. After ending the cycle and closing the door the display says\015\012draining but even though some water is expelled a lot id left in the dishwasher\015\012after the displays says END.\015

Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SGS09L02 Logixx Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SGS09A02 Logixx no Hot Water and not completing Cycle.


... Bosch 24 in. SGS09L02 Logixx Built-in Dishwasher

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own wat ... Bosch SHX46A07UC Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Hot water cycle and Drying cycle do not work on Bosch dishwasher


... Bosch SHU5315UC Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Bosch compact Logixx dishwasher (8401) will not start after it did turn on to start a cycle. Pump made laboured draining noises then seemed to cut out. Water remains in the bottom after last cycle.


... Bosch Dishwashers

My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks


... KitchenAid Dishwashers

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers

I have a built-in Bosch dishwasher SHU 4302 UC. It no longer drains the water out at the end of all the cycles. I have tried everything mentioned in the booklet (make sure water is hot, use the jet-dry stuff, make sure outflow hose doesn't allow water back in). I have to siphon out at least a good bucketful of water. (Also, only the regular wash cycle works, which is fine with me.)


The problem is a solenoid on the bottom of the unit. It is a small black cylinder next to the pump. It operates the valve that changes to the drain cycle. You can probably order one from Bosch ... Bosch 24 in. SHU43 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Bosch SHE43C05UC/22 Dishwasher cycles take 3-4 hours to complete. After cycle is complete, dishes do not dry and interior is not very hot (opening the door immediately after a cycle used to put you a


... Dishwashers

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Bosch SHU43C 06UC works fine except: No hot water. Hot water supply to machine ok! Machine goes thru its cycles and always cold. Thermostat?


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

We have a hotpoint DWF30P/17 Dishwasher which no longer heats or washes with hot water. The cycle completes the wash but no hot water. Can you advise? thermostat element controller


Before I went with the controller, I would probably try the heating element itself, they are usually not that hard to replace and may be cheaper. I know its not that much advice, but just trying to help. ... Dishwashers

Bosch dishwasher model SHV6803UC/12 - washing cycle finishes with substantial water in pan. Dishwasher turns on intermittently following cycle and drain small amount of water but never close to completely draining pan.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I`ll start by letting you know there are many things which can manifest in the manner you`re describing...or even how one interprets what you`re ... Bosch 24 in. SHX46A05 Stainless Steel Built-in Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch model SHX36L. The wash cycle is not ending, we have to open the door to stop it. We initially thought there was no hot water, but then realized the water was not as hot as it normally is.


... Bosch Dishwashers

Bosch dishwasher fills with water after cycle is completed


Sounds like you need a new water inlet valve. It's not shutting off completely, so water slowly enters the machine even while it isn't running. ... Bosch 24 in. SHU43 Built-in Dishwasher

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1378 seconds