Having problems with your Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher ?

Last couple of days bottom rack of dishwasher not been clean on 65o wash, having emptied and run the machine empty etc it seems that whilst there is water being pumped through the roof mounted vents and to the "spinner" attached to the upper tray, the spinner attached to the base of the machine is not getting a) any / b) sufficent water pressure to make it spin...im guessing the feed is blocked?


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Last couple of days bottom rack of dishwasher not been clean on 65o wash, having emptied and run the machine empty etc it seems that whilst there is water being pumped through the roof mounted vents and to the "spinner" attached to the upper tray, the spinner attached to the base of the machine is not getting a) any / b) sufficent water pressure to make it spin...im guessing the feed is blocked?


... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Frigidaire Dishwasher Model #FDB1500LFS2 After finishing all cycles, no problems at all. But if it was not in use for couple days some dirty water back up at the bottom. Then just let the machine run and wash another full cycle, everything is fine, but couple days of no using , dirty water back up again


... Frigidaire Dishwashers

Hi, we have a Neff dishwasher and noticed a couple of days ago that it took hours longer than usual for the dishwasher to complete its cycle. Last night after the machine had been on for about 4 hours we checked and although there was some water at the bottom of the machine it had not started to wash the dishes although we had heard noises coming from the machine. On opening the integrated door notice that the "check water supply" indicator was lit up. Do you have any suggestions as to what


... Neff 24 in. S5443X2 Built-in Dishwasher

Bosch SMS4012GB dishwasher. Refused to fill. Found tray full of water in base of unit. Mopped up water about 2 litres. Machine works but lower reservoir on the side of the machine with float switch overfills and overflow leaks about an eggcup full each cycle. What is causing the overflow please?


An electric switch activated by air pressure. This device detects air pressure exerted on it through a flexible tube connecting it to part of a water tub. \015\012When activated, this switch then opens an e ... Dishwashers

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Component failure Actually a Kuppersbusch IGV 645.2 Dishwasher There is a plastic conduit which takes water from the base of the machine to the upper spray arm. This now comes adrift from its connection at the base (behind the lower spray arm) on every cycle, resulting in poor or incomplete washing. It can be replaced easily and seems firmly inserted when done but is always adrift again by the end of the next cycle. Anyone any ideas?


Put a bead of silicone on the tube connection and let it set up good before running. If the tube is in good shape and only comes loose this should be an easy fix. ... Whirlpool GU2400XTP Built-in Dishwasher

Hi I have a Kenmore model 13742k. The dishes in the upper tray are not getting cleaned. The upper spray arm is not circulating. I dissassembled the components from the base leading up to the spray arm but there is no clogging. Water does flow out of the spray arm but prob not enough to turn it. The turbo components are clear as well. Any ideas? Thanks Richard


The top rack is not cleaning because of low water pressure from the wash motor to the upper spray arm. Assuming\015\012the top spray arms are clear of debris, remove the lower spray arm to\015\012access the wash motor. Remove the 4 torx screws ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

Hello, Hope you call help. I have a kenmore 13793K. Middle spray arm (attached to the bottom of the upper tray) is not rotating. It is, however, spraying water. Any ideas on what is preventing the rotation?


... Kenmore 13793 Stainless Steel Dishwasher

Hi _ We have a Stoves DW616 dishwasher which has started leaking water on filling from around the front door. The BGas engineer replaced the seals around the door with those from a Hygena which he said were the same and it worked fine for a few days and then a further deluge. He has now said there is a seal at the base of the door (just about invisible) and although he got a further Hygena seal this would not fit and he says that as it's obsolete the machine should be written off. Before I 'bin


... Dishwashers

BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and


... Dishwashers

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

The dishes in my dishwasher are not getting clean, particularly on the upper rack. It seems to be because the upper water arms are not spinning during the wash cycle. The bottom spin arm is working fine. I have cleaned out both upper arms as best as I could without removing them (above and attached below to the upper rack), as it does not appear that these arms are easily detachable. I am thinking maybe water is not making it up the line to the upper arms? I also have a lot of dirt in the b


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... GE Dishwashers

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

We have a Hobart dish washer in our bar area and when it sits over night there is a pool of water on the floor in the morning. When we open the door and look at the upper right corner in the rear of the machine we have a steady flow of water running down the rear wall. When looking at thge machine where the black 1 inch water hose comes up from the floor there is a plastic T in the line with an electric wire the goes into the side of the T. I am guessing tha that is a sensor valve that is suppos


The model is most likley a lx18,lx30,lx40.The fill solenoid valve is stuck open.Remove the 2 screws on the bottom front where the pressure gauge is.Turn the circuit breaker off.When you remove the cover you will see a bronze valve with a red hose goi ... Hobart Dishwashers

[email protected] Day E1 error. Opened up the filters to clean all possible blockage inside the machine. Water is pumped into the machine when starting, then there is a pause, then E1, then water is pumped out again, which does not inidctae a blockage. Opened both side panels, and flow of water is possible on the left side. What can be done next?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... LG 24 in. LD-12BW5 Free-standing Dishwasher

I have a Kenmore, Stock 15649, approximately 14 - 15 yrs old that worked fine until the past few days. The upper rack doesn't appear to be getting any water, as bowls and glasses are still dirty after being washed. It appears as though water would spray from the bottom, through a "nozzle" in the middle of the lower rack, then go to an arm located underneath the upper rack. I haven't noticed any obstructions in this path that would inhibit the water from spraying. Any suggestions (outsid


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1825 seconds