Having problems with your Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher ?

Water not draining from the machine

\015 My Bosch Classixx dishwasher is less than two years old and half way through the cycle the"Check water" button lights up and the water has failed to drain from the bottom of the machine. Been through it trying to clear what I thought was a blockage but I don't think it is. Feel it may be a faulty pump - heart sinks as that's what was wrong with the last dishwasher (also Bosch) and then the repairman said it wasn't worth replacing. Any tips?\015

Answers :

If it IS the pump, it’s often because some relatively minor item (piece of cocktail stick/bit of nutshell/etc) has found its way past the filters and is blocking the blades of the pump. It is relatively simple to remove the inlet hose to the pump and clear the blockage (a pair of grips to pinch and remove the retaining clip, then the hose will slide off the fitting on the pump). I did this several times on my previous (Hotpoint) machine – and suspect it is no harder on the Bosch (which I now have). If that doesn’t work, you are half-way to replacing the pump, which is not a difficult DIY job and I’m surprised any competent professional repair man wanted to write off a machine where the pump had failed. A new pump should cost around £40-£50 – less than a quarter of the cost of a new machine. DIY fitting would maybe take a couple of hours; a pro ought to do it in less than an hour.
We had that happen on our Kitchenaid dishwasher. The way we solved it is that we pushed the cancel/drain button on the front of the machine. Hopefully yours has a cancel/drain button.
Repair Help & Product Troubleshooting for Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Have a Zanussi 6344 dishwasher, when starting the machine it starts pumping en then stops. When adding water the same problem, starts pumping to drain the water and then stops again ? It drains perfectly, seems the machine thinks there's still water inside, is there some sensor that checks the water level or so ?


... Kuppersbusch 24 in. IG6344 Built-In Dishwasher

Hi, Zanussi dishwasher DE6344, when starting any program the machine start pumping (draining) for a while and then stops, lights start flashing saying that the draining is faulty. Checked the drainpipe and when adding some water the machine drains it perfectly, still the program won't start. Looks like it thinks there still water inside ? Suggestions ?


... Zanussi 24 in. DE6544 Built-in Dishwasher

Hi there My dishwasher (Miele G975 PLUS) drain light keeps coming on and the water won't drain. I can manually drain the water and the machine will then start again but as soon as it gets to the drain/rinse part of the cycle, the problem recurs. I have removed the non-return valve and it was clear of blockages so I am now out of options. The machine is only 4.5 years old. Any help would be appreciated. Thanks


... Dishwashers

Dishwashing machine not fully draining (2 inches of water remain). I have an open problem concerning this problem. I have a new pump. dishwashing machine not fully draining (2 inches of water remain) For this machine.


Following a cycle, a small pool of clean water inside the tub is\015\012typical. Excessive water means the pump isn't pumping water out\015\012properly, the drain hose isn't carrying it to the drain pipe, or the\015\012house's drain lines are backed ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

Whirlpool dishwasher ADG 7460 will fill with water ok and wash but will stop before it finishes the cycle leaving water in the machine. if you set it to rinse it will drain the water .... so the drain pump is working ..... water it drains is hot so the element seem ok ..... help


Hello & Welcome to FixYa Dishwasher not draining completely problem usually ... Dishwashers

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the ... Asko D1796FI Built-in Dishwasher

Hi, I have a Siemens SE44 dishwasher with Aquastop, which I bought recently. It was doing great for first 3-4 wash cycles and then it stopped functioning :( Now all it does is let the water in, and then drains it out- it doesnt do anything else. I can hear the water going in and then the machine drains the water,and this repeats. I tired resetting the dishwasher, checked the drain pipe, aquastop etc, and all seem to be in order to me. Any suggestions? Many thanks, stonerockyy


... Dishwashers

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

My dishwasher started making a whirring sound around 20 minutes into its cycle. I took off the drain pipe to check for obstructions, however it was clear. I started the cycle from the start again, and it started the whirring sound from the start of the cycle. There was a small amount of water that drained into the bucket where I had placed the drain hose, however there was not much water in the machine to start with (I checked when it started whirring the first time and there was no water in the


Hi.\015\012\015\012A blocked pump in absence of water won't be noisy from start. Check that\015\012 the whirring sound is not given by the spray arms. Test without baskets\015\012 and check the spray arms assembly.\015\012\015 ... Fisher and Paykel DS605I Built-in Dishwasher

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

There is water in the bottom of dish washer after finishing. If I start another cycle, everything drains, so it's not a problem with the hose. I hear water draining. I think it is the drain time. When the machine was under warranty, the service guy came and changed the drain time to longer. He told me how to do it, via the buttons, but have now forgotten where I put such great information. I have a 1996 built in model.


We have come up on this many many times. It is not drain time. There is a flapper in the drain hose located where the hose attaches to the pump with towels remove the hose and stick you finger in. It is and angled piece of rubber so it will be dif ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0895 seconds