Having problems with your Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher ?

Looks like program in electronic dishwasher has locked into a cycle. the machine will not drain even after resetting it. Also it will not restart any program or cycle after resetting and recycling power. The machine is a classic electronic bosch dishwasher It has worked perfectly for three months


Answers :

Im a old bosch tech . the problem is the module or the drain pump is stuck. if this helps please give me a 4 thumbs up post thanks.
Water won't drain away and/or machine gets stuck, the "END" light comes on and won't let you do a new load. (Note: my machine is a Bosch Classic Electronic - underbench model)
\012
\012Solution 1 - Grab top of drain filter, turn anticlockwise and lift out. Give it a thorough clean. Sponge out any remaining water and check for obstructions in the cavity below. Next, remove the white pump cover on the side of the drain cavity (there is a lug sticking up and you can use your fingers or a spoon to gently prise it off). You will see the white plastic blades of the pump. Remove any obstructions and then replace the pump cover, clipping firmly back into place. Test to see if machine is now working.
\012
\012Solution 2 - If the above fails then pull the dishwasher out from under the bench. You may need to unscrew two holding clips in the top left and right hand corners at the front of the machine that lock it in place (underbench model). Once pulled out, it is a good opportunity to clean away all the accumulated dirt underneath (yuck!). Tilt the machine over onto its side to the left and then to the right. Turn the machine OFF then back ON again. This may need to be done several times before the problem is solved.
\012I had to do this this morning when the "END" light was stuck "ON" and I could not do a full load of Easter dishes. At first I tried the 45 degree tilt and no luck. So then laid the machine completely over on its side, left then right. Still no luck. Said a prayer over it, laid it on it's side again, but this time with a couple of jolts by letting it drop the final inch (left side then right side). Hallelujah, it's working and my Easter load has just finished. So I can kick back and enjoy the holiday.
Repair Help & Product Troubleshooting for Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Looks like program in electronic dishwasher has locked into a cycle. the machine will not drain even after resetting it. Also it will not restart any program or cycle after resetting and recycling power. The machine is a classic electronic bosch dishwasher It has worked perfectly for three months


Im a old bosch tech . the problem is the module or the drain pump is stuck. if this helps please give me a 4 thumbs up post thanks. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Blanco BFDW6 dishwasher drains and sounds like it is going to start but stops after 2-3 seconds. Yesterday it was playing up and made a fairly small puddle on the floor. Electrics seem to have been a problem from early on as after a few months it would let me open it during the beginning of the cycle to add items without needing to restart program. I am not sure if problem is electric (may need a reset?) or due to anti-flood feature.


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Global 450 dishlex dishwasher. Had the handle replaced 2 months ago. After that the ready light did not switch off as before. Now it only rinses. When you set the normal wash cycle the lights for Pre Wash, Wash and Rinse all come on. Pots cycle, the Pre Wash, Wash, Rinse and Dry all light up together, hence the machine thinks it up to that stage of the cycle. Can this be repaired or not. The machine is approx. 12 -14 years old.


... Electrolux Dishwashers

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

I have a Indesit IDL 600 S dishwasher. Yesterday a cycle there was unfortunatly a power failure. I am now, unable to get the machine to regain any of it's cycles, it just remains stuck in it's first position (light one on) and will go no further. Is there a way I am able to reset the machine? Many thanks


... Indesit 24 in. IDL500 Built-In Dishwasher

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers

My cda dishwasher cw448 is 18 months old, and has recently begun to stop before the end of the cycle. When I open the machine, 3 lights flash, (one of them the rinse button), and the machine bleeps repeatedly. Why doesn't the cycle complete? I've checked the filters, the spray arms, all the dispensers, and manual doesn't give any answer. This doesn't happen all the time, but is occuring more often now.


... Dishwashers

My GE dishwasher will not turn on. The electronic touchpad will not do anything...I can't change the wash cycles or reset anything. Is there a reset button for the touchpad? Or do I need a new dishwasher?


... GE Tritonr XL GSD6260JCC Dishwasher

We were running the dishwasher on the Intensif 65 degree cycle and it is now stuck on Lavage and will not reset. How do I get the machine to reset so that I can run a new cycle?


Have you tried to turn the mains power off?\015\012\015\012What happens when you turn it back on?\015\012\015\012It will help if you proide the make and model no. of your dishwasher.\015\012Also please clarify what is La ... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Hotpoint dishwasher lft 114 - machine will not start the wash cycle - power light on, can step through each program usign the Program button, but when the door is closed nothing happens. No residual water in machine as far as I can see. Any ideas?


... Dishwashers

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

I have a GE Profile Triton Dishwasher and it has worked fine for about 8 years. Suddenly it will not reset. The reset light blinks after reset but you can not choose a normal cycle afterwards. I shut of the machine by pulling the fuse box. I turned it back on but again it will not reset?


Hello, how are you?\015\012It sounds like you have a stuck key on the keypad, preventing you to push any other key.\015\012I've seen this problem many times in the past 4 years.\015\012Good luck.\015\012Ned ... GE 24 in. Profile PDW7800 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2362 seconds