Having problems with your Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher ?

Hi I have a Siemens SE26T252GB/01 dishwasher which won't drain. (The "check water" light comes on). I have checked all the filters/drains and I think the fault is the drain pump which I would like to replace. I can remove the side panels but cannot remove the base to get access to the pump. Can someone help with instructions or a diagram please? Many thanks


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi I have a Siemens SE26T252GB/01 dishwasher which won't drain. (The "check water" light comes on). I have checked all the filters/drains and I think the fault is the drain pump which I would like to replace. I can remove the side panels but cannot remove the base to get access to the pump. Can someone help with instructions or a diagram please? Many thanks


... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

Due to the my Indesit IDL 530 dishwasher not draining properly, I turned it onto it's left side, removed the base plate and pump and checked for blockages in the pump and associated hoses, which were all clear. However in re-assembling it I have forgotten which way round to connect the twin wire plug to the base plate. I cannot find a relevant wiring diagram online and therefore cannot tell which is the correct way around. I then guessed and re-assembled it anyway, and as you might have g


Hi.There is more than one wire going from control board to the tub. If the connector can be plugged either way without forcing it, then usually does not make any difference the way you plug this determined connector. It will be usef ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Front panel My dishwasher wouldn't drain. I read I had to remove the front panel under the door and get to the hose to look for a blockage. I screwed out two screws on the side of the dishwasher and removed the white front panel just under the door. But then there is another metal panel and I can't loosen it. Is it just stuck or is there soem way of doing this? Elmi


Did you knock out the plug on the disposal before you hooked up the drain hose ? ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a Bosch dishwasher model no. SHU66C05UC that does not drain properly. After checking for a clear drain tube and finding no problem. I removed the left side panel and found that the red float was not rising in the tube. If I pull up the trigger device to engage the pump switch the machine drains. What causes the float to stay down and what is required to free it? Thanks for any help.


Water in the base. ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks. My dishwasher showed the error code either OE or E1, I think it was more OE. I stuck my hand in the filter in the bottom of the machine and then it was okay but the next time it was used it leake


What sort of soap powder do you use\015\012some soap powders foam a lot in machine causing dishwasher to leak through seals\015\012also check that the machine is square that is the door is closing parallel with cabinet\015\012do no ... Dishwashers

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

No kinks in the line. Vent at sink is clear. Will pump some water just not all of it. Pulled left side panel off and removed hoses-no blockage. Pulled drain hose off and turned plump on, seemed to have good pressure/volume. Is this a timer issue? or control panel? Model SHU4022UC/U06


Alright, so you have a Slow Filling Dishwasher. In order to keep small particles of dirt and minerals out of the pumps and nozzles of dishwashers, manufacturers install a small screen in the primary inlet water line to trap any contaminants. Over ti ... Dishwashers

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

I have a Bosch SGS46E22GB Exxcel dishwasher. It is failing to drain or pump out dirty water. About a year ago we had this fault and the engineer replaced the impeller jug. He showed my wife how to clear a blockage with the left hand side panel removed. I can't get the panle off so am looking for instructions on how to remove it. Thanks


... Dishwashers

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks.


There are screws on the inside of the door on a lot of those\015\012try to tighten them down a little sometimes that can cause a leak. ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Hi, we have an aquarius hotpoint df61 and it goes through the cycle but does not drain out the last few inches of water and the wash is not as good as it should be, have unscrewed the plastic bit under the filter thing to see if there is a blockage there but nothing, have now taken off the top and side panel to try and get to the pump, currently on it's back but hard to access underneath and not sure how to remove the solid bottom of the dishwasher..please help!


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Bosch dishwasaher model SGS53 has stopped working and has water in the bottom of it , i have cleared this and checked the small impeller for blockages - this is ok. i have also checked the water inlet filters and the drain tube is clear . I have the top and left sid panel of and when i lift the red rod it allows watrer to come in but stops if i release the rod thr lever in the base of the machine int which the red rod fits appears th be at its lowse level and therefore the red rod cannot be p


... Dishwashers

During the cleaning of our dishwasher (ADG7952 model), it started beeping and there was a F8 message reading on the panel. The water has not drained away. We have tried to clean the filter and remove excess water left. Unfortunately, we cannot find the user manual-not sure that it was left when we moved into the house. Not sure what the problem may be?


... Whirlpool 24 in. ADG7952 Built-in Dishwasher

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Screw drop Hi I was installing my new LG dishwasher and I droped a screw in the hole in the side panel where you can put a screw to connect to the side of your cabinet. There is a small plastic cover which I removed where you can screw a screw into the cabinet. However the head of my screw was too small and fell in the side panel. I can not get the screw out or see it now although I know it is in the dishwasher. Is there anyway of getting it out or will this cause a problem? Since it is in t


A great retrieving tool for this is a flexible shaft magnet wand. I strongly recommend this tool be placed in everyone's toolbox.\015\012\015\012as far as leaving it there if not found? probably safe from electrical. will years of vibration allow it ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

Won't drain I'm helping my daughter long distance,their dishwasher won't drain. I had her remove the course strainer to check the well for debris. She said she cannot get in it because the sprayer is in the way. How is the sprayer removed to access the drain well in the Maytag DWU dish washer?


In most cases the blockage is at the end of the drainhose, where it connects th the "peatrap", simply removing the hose clamp, then hose and inspecting. If no blockage found there you will need assistance. If you want, you can funnel your hand over t ... Maytag DWU9962 Dishwasher

How do the back and side panels come off? I have removed the screws from along the front around the door seal and from under the kick plate, but the top panel is somehow just clicked on keeping everyt


... Bosch 24 in. SGS56E02 Exxcel Built-in Dishwasher

The dishwasher will not drain. The motor hums. We have tried to remove the central unit inside the dishwasher, but cannot remove the inner black disk --it has a bolt, but we cannot get a good grip to twist it out. We suspect that under the mesh covering is a lot of gunk that needs to be cleaned out.


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain ... Dishwashers

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Am trying to deal with source of non-draining problem-drains but not complteley. Have remove three screws from love plate but cannot seem now to remove the assembly (which also golds the lower spray rotor). Any ideas.


If it is a Bosch, the following just worked for me: pull out screens and on left side of sump (looking down into bottom, 9:00 position) has a torx screw holding cover over drain pump, remove screw, cover has tab towards backside to lift towards you. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1399 seconds