Having problems with your Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher ?

Hi There, the quality of wash on my Bosch dishwasher has reduced (especially on top shelf) to a point where it is almost not worth using. filters etc are clean and no issues with water enttering the machine. i am assuming it is the power of the spray which has reduced , what can i do? many thanks, Mark C


Answers :

All the jets must be clean especially the drive jets at the ends of the wash arms, these drive the arms around thus allowing jets of water to reach every piece of crockery.
Repair Help & Product Troubleshooting for Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi There, the quality of wash on my Bosch dishwasher has reduced (especially on top shelf) to a point where it is almost not worth using. filters etc are clean and no issues with water enttering the machine. i am assuming it is the power of the spray which has reduced , what can i do? many thanks, Mark C


All the jets must be clean especially the drive jets at the ends of the wash arms, these drive the arms around thus allowing jets of water to reach every piece of crockery. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

SGV55M43EU - The machine does not spray the water even if the pump works. The only way to have the water spray is to add water manually directly inside the machine. I checked the inlet valve (acqua-stop) , it seems to work. many thanks, Alessandro


... Dishwashers

I have a Siemens SE65560/12,I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was ''I'' indicated, or maybe means ''1''. Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling MoreI have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was ''I'' indicated, or maybe means ''1''. Now


... Siemens Dishwashers

My ge nautilus dishwasher is not having water run thru the cycles, i ran the machine 3 times and the dishes were still not washed and the tablet not dissolved. My husband sprayed water and cleaned the inside, he removed the filter basket and now the water he sprayed inside will not drain out!!! Please help!!!


... GE 24 in. GSD2220Z Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Upper spray arm is not turning round even though water is coming through. We have checked the internal system for blockages and the machine is filling / draining as normal. When a full programme is run, many of the dishes, particularly on the top shelf, are dirty and many have hardly been touched by water. Could a pump or other part be faulty?


I found the problem to be neither blockages of the upper arm or roof spray arm or the upper basket arm hitting the the back of the dishwasher. the problem was that the pump inlet where the food scraps are macerated was blocked with all manner of gung ... Dishwashers

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Bosch srs43c12gb/14 classixx dishwasher spray arms not spinning. The dishwasher goes through normal cycle but the spray arms are not spinning, I have cleaned them and the filter inside the machine and the one on the water hose, still not spinning. the machine is about 4 years old.


... Bosch Dishwashers

We are having a problem with our LG Dishwasher. The machine is washing for about half an hour and then will stop and report an E1 error. According to the user manual this means "Water leakage in Hose connection" or "Water is leaked by damages". We have checked the diswasher's water connections and can't see any water leaking out. We have also cleaned the filers and checked the spray arms but that has not made any diffrence. Any suggestions what this error means and what we can try to resolve it


... Whirlpool 24 in. DU940QWD Built-in Dishwasher

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

My chef classic dishwasher is not completely cleaning the dishes. There is no obstruction to the tablet/powder door opening, although there is a small amount of powder left at the end of the cycle. Both top & bottom spray bars are clear & rotate, the water is heating & there appears to be plenty of water getting water into the machine. Drain filters are also clear.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Magic Chef CDB6100 Built-in Dishwasher

Have a LG model LD-14AW2 dishwasher which has done good service for many years However, it now sems not to have enough water pressure to operate all the rotary sprayers at the one time - thereby not cleaning properly Have purchased a manual and raken the whole machine apart looking for a partial blockage of the water ways - non found - all looks perfect - still no water pressure I would suspect the pump - however, would have thought a pump either gave full service or stopped - not parti


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Dishwashers

I have a ADG 450 dishwasher, it has suddenlt topped completing the wash cycle. it runs for about an hour then sits and beeps. If i open the door, the machine is full of water and it looks as though it is trying to spray more water in, thn stops and beeps. If i turn it off and on at this stage and run the rinse cycle, the water clears and the dishes appear to have been cleaned. any thoughts? it happens with all wash cycles.


... Whirlpool Dishwashers

I have water left over after each wash and it is really cloudy? I use the right amount of dishwasher liquid, etc. It has hot water. When I first got it about 2 years ago, it did not have this issue. I assume a little water left after the wash is okay? But, it is milky cloudy for the past 3/4 months now. I have a Maytag Legacy Series Quiet Series 300 machine...


Try running your disposal for a few minutes and then run through the rinse cycle. mine does this too sometimes and i just need to clean my disposal in my sink as some stuff gets caught up in it. ... Maytag 24 in. MDB9750AW Dishwasher

Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was "I" indicated, or maybe means "1". Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling out the plug from the wall socket, and reconnecting the machine, on the display stays the indication "I" or "1". I can't do anything ...what's the problem


I do not know if you been talking to other experts but without knowing how far you went with them if any I may need to start from the beginning these units are sold in Europe and not the US is that true. Second from your post you went t ... Dishwashers

I have a three-year-old Sears Kenmore Elite dishwasher. I find that despite the fact that we scrape and rinse our dishes before loading the machine, after each three months of use (two loads a day) or so, I have to take the machine apart (spray tower, racks, bottom impeller, bottom screen housing, food grinder cover) and clean-out the food grinder area, for it fills-up with sludge. The sludge restricts the water flow and there isn't enough flow to turn the impellers via that steering jets.


Have you tried different detergents? Some detergents after getting wet and going through the wash cycle with the debris from the wash turns into a grease substance that grimes up in some dishwashers. Try running the machine with hot water this someti ... Dishwashers

My detergent is always still stuck in the dispenser. The water temp and pressure are both fine, the machine is clean as well as the spray arms, and the door opens but water just isn't dissolving it. I have tried powder, gel, tablets, and gel packs!!! Please Help!!!


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Magic Chef 24 in. DU2500 Built-in Dishwasher

We are getting a grit on the dishes on the top rack. We have done many things to solve the problem. Running tang crystles, runing CLR through it, taking it apart to check for blockages, checking the impeller on the pump, blowing comprssed air through it, scrubbing the inside many times. The funny thing is it only happens about every third wash cycle or so. The upper spray arm is free with no obstruction. The dishes on the bottom rack are clean. We use Electosol and jet dry. Our water is softened


Hello John\015\012\015\012Thanks for all the detail. It's far more than I usually get to start with, but please could you also answer the following quick questions:\015\012\015\012- Are the particles hard and gritty or is it f ... Asko Dishwashers

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

My Kenmore Elite suddenly stopped filling with water. I pushed start but when I checked it hours later the soap dispenser door had opened, the soap is just lying in a puddle, and nothing is clean but the clean light on the front panel is blinking. I tried again to no avail. Any ideas? I've had the machine since it first came on the market and have had other issues with it--it never drains completely, it makes sounds like someone revving a sports car engine when the drain pump is engaged, my dish


Https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a4 ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Not cleaning on top rack. Pump, fill tube asm. & spray clean. Has any seen if this issue could be the deverter motor in the pump or the control board?


Just to review, the LG dishwasher family, including the LDS5811 has the Verio motor and the check valve that diverts water from the bottom rack to the top rack. If the valve is blocked/jammed, this would cause the symptom you describe. T ... LG 24 in. LDS 5811 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2020 seconds