Having problems with your Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher ?

I have run the test cycle and the quick wash and pre-rinse lights are illuminated. Does this mean a water sensor and filling fault?


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have run the test cycle and the quick wash and pre-rinse lights are illuminated. Does this mean a water sensor and filling fault?


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

E4 error light comes on, dishwasher won't run, this apparently means water is on a sensor, have removed water from collection tray in bottom, tilted machine backward to dry out sensor, left for 24 hours, machine still won't run. Currently a very small new counter top but a useless dishwasher.


The problem is related to the floater assembly inside the dishwasher. It is filling up with gunk and stop working properly. I found out the hard way after a good spill. The solution is easy but takes a bit of time.1. Unplug the power and water h ... Danby DDW497W 22 in. Countertop Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

"Sensing" Light Moved a 5 year old dishwasher that was functioning just fine to a different location. Hooked everything up and gave it a test run without any dishes in it. Fills and heats water properly, then buzzing noise heard for a ling time and then it drains the water out, with out circulating the water into the washer arms, etc. Any guesses? Could something have gotten lodged in the pump during transport?


There is a relay on the soap dispenser, if it is a Kenmore quietguard 4, I had the same type of noise, the repairman replaced the dispenser, which to me made no sense, because the relay is activated from the control board. After the $130. for the soa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

I have a Kenmore diswasher model 587 1525. I can hear the water filling and rinsing, but during the wash cycle I do not hear the motor. At the end of the wash cycle and when I open the door I see the detergent tablet is sitting on the floor. The dishes are not cleaned. Does this mean that the motor has failed or is it the control card. I can hear some clicking noise while the motor should be running. Maybe solenoids cycling.


... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found o ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I have a frigidaire dishwasher 950 series. Filled washer hit start button no light but water is running. Wash cycle only no rinsing. And it will not shut off.


... Frigidaire Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

D1876 Asko dishwasher doesn't fill. It runs fine if I manually fill the unit with a couple of pitchers of water. Likely culprits seem to be a faulty water level sensor or water fill valve. Any suggestions on how to proceed with troubleshooting/repair?


Hello, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko ... Asko D1876 Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

Bosch shu9905 the wife **ticed water level was **t emptying...thought i left dishwasher on ...so continued and then ** water was coming out and burn smell ..did a test and the scrub wash lite = water filling fault (over or under filling)


Check the drain pump. First, manually initiate drain by pressing the second and fourth buttons on the keypad at the same time. If it pumps out, disregard the rest. If it doesn't at least hum, check for power at the motor.\015\012Remove lower ra ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2150 seconds