Having problems with your Bosch 24 in. SGV43A03 Built-In Dishwasher ?

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Answers :

Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...\012
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance\012DishwasherResidue and Film on Dishes\012

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes
\012
\012';'\012'';\012'\012;'\012;
Repair Help & Product Troubleshooting for Bosch 24 in. SGV43A03 Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

I have a Bosch "Classic Electronic" dishwasher that has been in use for only 18 months. If it helps - SGU53E05AU/30 is marked on top of the door.. my problem is that on the last cycle, the water won't drain so I am left with lovely clean dishes but there is water up to the drawer line present and it won't drain until the next wash. I have cleaned all the filters and ensured the pipes are not obstructed. It is odd that it only does it on the last cycle. Could it be the microchip?


Hi there,\015\012\015\012thank you for providing the model #, that helped me narrow down the troubleshooting.\015\012\015\012try the following to fix your problem:\015\012\015\012check for blockage or kink in the d ... Bosch Dishwashers

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

No Heat Had the blinking clean light problem, reset, and it fills and runs, but element not heating. Element reads 10.6 ohms, both door switches seem to be making. What else might be causing it not to heat? Is it possible to find a wiring diagram or schematic?


Should be a tech sheet stuck to inside of the bottom toe panel.Switches may check OK with no load applied. There is also an over temperature thermostat that may be open. If all checks OK, control may have failed. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

My Hotpoit FDL570g dishwasher (that is less than 2 years old) is tripping the circuit breaker originally during a wash and now when the unit is switched off and and door is closed. I thought it may be a door lock / microswitch problem and replaced the microswitch. The dishwasher was good for four seperate washes but now the problem has come back when crockery is loaded when the machine is switched off. I'm going to check for bare / rubbed leads but not expecting to find this with a dishwasher of


Hi,\015\012\015\012If your washer is tripping the breaker when it is switched off, this is often a sign that water has leaked - or is leaking - into the bottom of the washer under the washing compartment where there are lots of exposed el ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Kitchen Aid Dishwasher KUDS03ST We built our house and had this dishwasher sitting in the box for almost 2 yrs before finally using it. After finally installing it I find that occasionally the door to the soap does not open for washing as I find out when the dishes are supposed to be clean and I open the door to hear the soap then pop out of the dispenser. How do I fix this problem?


I have seen a lot of dishwashers that have this problem if they have a flip open lid for the soap .. often its caused by the top adjustable tray blocking the soap door from opening .. i put a camera inside to figure out what was happening ..in some ... KitchenAid Architect? II U SERIES KUDS03ST Stainless Steel Built-in Dishwasher

I have a KitchenAid but model # KUDI24SEWH1. Can not find it on your list although another model without the last letters 'WH1' is on it. Anyway, my nephew ordered the parts he said needed to be replaced. One was the top water feed tube and bearing which he had no problem replacing when the part came in. But, he is having a very difficult time opening up the front door to replace the soap dispenser. Removed the 6 screw (three on each side) and the two at the top of the door but that is as far


You don't Use the WH2 just the first 6 letters and numbers.\015\012Jim ... KitchenAid KUDI24SE Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

I noticed water coming from underneath my dishwasher so I pulled it out from the wall and found that underneath the factory installed installation there was a screw missing that holds the top dishwasher rack. The hardwood floor and bottom of the cabinet is ruined. While finding this problem, I also found rust on the bottom of the rack. Who do I need to speak with about this problem?


Speak with who you purchased the dishwasher from. They will be able to point you in the direction to get a replacement and file a complaint. All of this is provided you bought the machine in the last year. ... Kenmore Dishwashers

I have a Whirlpool DUL300XTLQ3 Queit Partner III. The cleaning blades stopped moving-started it-waited awhile-opened it-the blades were in the same position. Took the bottom blade+filter cover off. Then I held down the metal piece on the case and switched on the micro switch on the door to see it running with the door open. The water shot straight up about 4-5" that's it. This does not seem to be enough pressure for the water to get all the way up to the top spinner. Am I looking at a new pump


If there is not enough water, the dishes would not get cleaned. Thiscould be caused by a partially closed water shut-off valve (locatedunder the sink), or a faulty dishwasher water valve (located at thebottom of the dishwasher, behind the kick panel, ... Whirlpool Dishwashers

F1 error code due to water coming over the top of the top drawer at beginning of cycle. Previously, I had this code and followed the instructions found here and resolved the problem (a foreign object had blocked the drain). This is different and I need to find out WHY the water is flowing over the top. Could the top drawer just not be sealing properly when closed?


Hello,\015\012\015\012Here a link to a F&P repair video.\015\012\015\012Dish Drawer Repair Video\015\012\015\012http://www.appliancerepairlesson.com/shop/dishwasher-videos/fisher-paykel-dishwasher-repair/ ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

Hi I have a Neff built in dishwasher s5453X1GB/70 about 4 years old. Never had a problem before. Came downstairs last night to find the kitchen floor flooded. Water also still in machine. But must have been near end of cycle as plates all clean. I have read other links and opened pump compartment in centre of machine and syringed out all water and cleaned fan. When i switch on machine it is still making odd humming noise (emptying cycle?) I have read about anti -flood valve etc. Any more tip


... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

I have a LG Dishwasher (LDF6920ST) The top rack is not working at all, even after I took everything out to clean. I really found northing when cleaning either. The dishwasher also has been smelling hot, and I saw a few arc (sparks) coming from the lower center with the kickplate off. Since then I have turned it off, and switched off the breaker. What do you suppose is going on?


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

I haave dishwasher model 665.743893. The top dishes do not come clean and I suspect that the top arm is not rotating because it is in the exact same position each time I open the door and at the end of the cycle. I took it off to remove possible debris but found none, though difficult to look inside. Do you have any suggestions?


If you can use a high-pressure washer or air hose to blow it out, that would be helpful. Otherwise soak in hot dishwater. Do check the hose to the arm and make sure that is not blocked as well. ... Kenmore Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

My Bosch dishwasher, S9J1F will not clean things properly, I've changed the arms, cleaned it. I think the arms don't seem to spin properly, (I bypassed the door switch so I could see them spin)I have tried new arms though, pump pressure or ?


Not enuff water in it or pump blockage or bad pump impeller. if you ran it with the door open even if the arms didn't turn you should have got drenched is the bottom covered with water about 1 inch deep some times the fill valve screens get clogged a ... Bosch Dishwashers

Hi, my hotpoint aquarius df61 makes all the noises of washing, i hear the water going in, motor is running, however i dont believe the spray arms are revolving, so the dishes are not getting clean. i have cleaned the individual holes in the spray arms, but i don't think the water is getting up the back pipe and into the top spray arm. it does not spin at all. no problems draining. help please. and were can i get a copy of the user guide, free preferably. thanks


How old is your machine? it is posible to have something in the watwr pump, you hear the water and the motor, but the fan of the pump (washing pump) is blocket. also the pipes hat make connection to the water pump and the arms. at someoane i found gl ... Dishwashers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1358 seconds