Having problems with your Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher ?

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Answers :

Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering nothing is froze..at least you'd hope lol. I have a copy of it at home and I can likely post it later, ( I'm on my iphone presently ) but essentially what it say's is this...Remove the pump fitler ( inside the tub under the bottom rack ) locate the hole to your right down in the sump well, you should be able to see it with a flashlight or well lit area. Once you've located this hole ( it's providing access to the wash impeller without pulling the unit from the cabinet ) reach in with a 8mm nut driver and locate the end of the impeller and turn it clock-wise until it feel's to turn freely. Give it a test perhaps in a rinse cycle before you put all the filter and screen back together. It should be fine unless the motor is seized, we'll cross that bridge when we get to it, try the repair tip for now.\015\012\015\012Let me know how that help's and/or if you need further assistance. Thank's for visitng "fixya" for you repair tip's.\015\012\015\012If this is indeed helpful please rate the solution accordingly, if not, again please let me know.\015\012\015\012Thanks again and good luck.\015\012\015\012\015\012Macmarkus :)
Repair Help & Product Troubleshooting for Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My Asko D1606 doesn't seem to be filling/retaining enough water to pump actively through the swing arms. When I add a litre or so of water in manually and hold in the door catch, I can see it appear to start working properly. The tablet is still sitting on the bottom of the dishwasher after the cycle has ended and the dishes are still dirty. The pump sounds all right and it is emptying fine. Also, probably due to the lack of water, the cutlery basket has melted right through, and I am sure any p


Check to see it the dishwasher has been pushed back ever so slightly. The water coming into dishwashers and exiting are on timers and if the hose is pinched this can affect it. Your dishwasher may appear to be in the same place but just pull it forw ... Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

I have a Siemens Avantgarde dishwasher. It fills with water, the water doesn't heat, it doesn't start the wash cycle. It continues to work through the wash cycle and doesn't pump out or refill with water during the cycle. It pumps out right at the end.


... Siemens Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

Bosch SHV46C Bosch dishwasher (SHV46C13UC) doesn't "start". When I start the cycle, it makes a noise but doesn't fill with water. The drain pump is working because I poured water into the basin and watched it disappear. The noise that it's making is a constant low-toned rumble/hum. I sometimes would hear this noise at the end of a cycle when things were working fine.


Replace the fill valve that sound is it trying to open ... Bosch 24 in. SHV46C13UC Free-Standing Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?


... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1926 seconds