Having problems with your Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher ?

Bosch SHE44c getting a E6 code????Just finished E1 code by re-soldering the board and the first wash after fixing that error, I get an E6 code and it did not drain. During the repair of E1 code, I cleaned all hoses out and made sure I had no problems...What is the troubleshoot to search for E6 code?


Answers :

Thanks, that perfectly nailed my problem. Bad / burnt solder joint on a SHX45P05UC/57 model. A little solder, and it may last a while. But next it fails that way I can order the motherboard without even opening it up.
Repair Help & Product Troubleshooting for Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHE44c getting a E6 code????Just finished E1 code by re-soldering the board and the first wash after fixing that error, I get an E6 code and it did not drain. During the repair of E1 code, I cleaned all hoses out and made sure I had no problems...What is the troubleshoot to search for E6 code?


Thanks, that perfectly nailed my problem. Bad / burnt solder joint on a SHX45P05UC/57 model. A little solder, and it may last a while. But next it fails that way I can order the motherboard without even opening it up. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

GE model GSD600003 repair manual: Before you answer this, please tell me if I will be charged for the answer, in case I'm not interested at this time. Do you have a diagram of the drain area and water inlet area? I took apart the plastic drain cover for cleaning because it was had pink mildew all around it where residual water pools. I cleaned it all up and put it back and now the dishwasher doesn't fill with water (none comes in). I'm just a guest trying to troubleshoot for relatives, so I'm


I'm not sure how mildew can grow in a dishwasher that is working well, but after cleaning it and putting things back together, it does now seem to be working. I thought that the water wasn't filling but I guess the heating element heats up before the ... GE Dishwashers

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

Our dishwasher, Model Automatic G572 SC runs, but does not drain. I have cleaned all the rotating sprayers, have made sure that the disposal is clear, and have checked the various parts in the base of the dishwasher. We had this problem a few years ago, but after letting the dishwasher sit for a few days, it corrected itself. I don't want to pay for the repair and heard that you can walk me through most simple problems. Help! Thanks.


... Miele Dishwashers

DD602I USA v2. Runs approximately 10 min then beeps continuously and on the front panel the middle light is red and on the inside panel the "Del" "Fast" and "Rinse" lights are red. What is this fault code indicating? I have made sure spray arm, impeller assembly, are clean and not blocked. No kinks in drain line. Induction motor sounds a bit noisy. This is only a problem with lower drawer, top drawer works fine. Thanks, Keith


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a ADP5600, starts but then cancel/off light flashes 8 times. We have cleaned filters (were fine) and checked drain hoses as per troubleshooting in manual, what else could it be?


... Dishwashers

Normal wash light blinks, machine will not run. No reset key code exists on the kick plate or inside the washer door panel. I have cleaned to drain hose and hot water supply is ample. Thanks Model 16029


... Kenmore 24 in. 16029 Built-in Dishwasher

Hi there, I have a Whirlpool Quite Partner 1 dishwasher. It was working fine until today the water would not drain. I detached the drain hose and it was clean as a whistle. When I had the drain hose off I ran hot water and it was draining through clean. What else could it be? I have no idea how to fix this. Thanks.


Hi,Here is a tip that I wrote that will help you with your dishwasher ... Whirlpool 24 in. DU900PCD Built-in Dishwasher

Brown scum accumulates under the large circular aluminum plates on the bottom of the drawers. Has to be cleaned out every 1-2 weeks. We have never had a dishwasher that required so much maintenance. We think it is the size of the drain. Can this be fixed by installing a larger drain hose. We have cleaned out the drain hose and it doesn't stop the problem.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My dish washer isn't cleaning the dishes well. There are little particals inside of every cup and on dishes after it is done. I just emptied and and now I'm running it with bleach. But before I started it I looked at the drain hose under the sink. The drain hose had water in it. The drain hose is going uphill from the dishwasher to the sink so I don't know if this is normal to have some water in the drain hose when the washer completes since it's not would have to pump uphill to get to the garba


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Hi, I've got DS 603 single draw dishwasher Ser. No. CPM 739878, It has given a fl code for the flood switch. I have removed the draw and made the observation that the lower steel housing has partially flooded, hence the code. I intend to replace the flexible hoses Input and discharge hose. I am wondering once I replace the hoses, dry the housing and associated printed circuit bourd area should the fault code reset its self or is there further tech. assist required. The draw was manafactured


In the catch basis there is a printed circuit board that contains a sensor that detects moisture. Once throughly dry however, the sensor will no longer sense moisture and the flood code will cease and desist.BUT before replacing the hoses, (alo ... Fisher and Paykel Dishwashers

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

My GE Monogram ZBD4500 dishwasher does not drain completely at the end of the cycle. If I run a couple of manual cycles afterwards it eill eventually drain completely. Drain hose is clean, pump suction sump looks clean, drain pump impeller appears OK, discharge check valve assembly is easy to blow through in direction of drain. Do I have a sequence switch problem?


I bloody lostt you! are you still there? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a whirlpool dishwasher errors say F8 E1 dirty filters, kinked drain hose, syphon hose connection closed I have cleaned the filters also the drain hose is not kinked so it must be syphon hose


... Whirlpool Dishwashers

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

Dishwaher wont drain-checked drain hose and its clean


The problem is most likely the drain valve. It is electrically operated and with your problem it is the most common cause.If you need more help, post a comment.Thanks, Tim ... Kenmore 16719 Dishwasher

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Dishwasher not draining E25 error code (Bosch exxcel) . I have cleaned filters & removed pump inspection cover to check / clean debris I have also checked the waste water pipe is not kinked, it runs for 1hr 15 mins last time and then cut out with the error code displayed.


Gr8 stuff klaudi & Nypmh - rocking it back 45% worked a treat. Bloody BonzaShell XX ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1527 seconds