Having problems with your Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher ?

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Answers :

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually is with the control...unfortunately. This is commonly associated with a heating fault as you suspected, hence the odor and poor cleaning on Bosch built dishwashers ( various models including Bosch, Thermador, Siemens, Gaggenau, and Neff ).


Since the issue is likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).
These are the steps you'll need to follow to resolve it or at least investigate.

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg


The culprit will 99% of the times be one of the pins from the heater relay,

9f1823d.jpg

**Flip this over and inspect the solder joints, it will be obvious when you see it.**

This ones new, but it's where to look...

9119d99.jpg


...hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...this can also manifest as a long cycle time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning, no heating ( don't be fooled by the homes inlet hot water temperature ) as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e. ( this may differ from your specific model, but the same rules apply )

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last.
Bosch recommend`s replacing the control and I don`t pretend to speak on their behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**


If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau/Siemens, to service your machine.

\015\012Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.

Good luck.

Regards,

Macmarkus :)
Make sure the disposal is not blocked with gunk.
Also your drain waste line under the sink.
The heater in the dishwasher may have failed causing extended was times.
Repair Help & Product Troubleshooting for Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Hello,Welcome to FixYa ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Dishes on top rack on not getting clean on the outside e.g. the outside of an inverted cup is dirty and dirty water is collecting in depressions. There doesn't seem to be a mechanism to rinse the dishes from the top. Also water not hot on any cycle so probably need a heating element. Where can I purchase one near 85204 zip code


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Ariston Technologies L63SNA Stainless Steel Built-in Dishwasher

Dirty dishes the dishwasher sounds and appears to be operating normally but the dishes are not getting clean. now i've noticed dishwasher soap still in the dispenser after the washing cycle has been completed. I'm thinking maybe i have plugged water jets? Anyone have any suggestions? Thanks.


Plugged jets, possiblemore likely it is leftover food reminance left in the pump area. and on certain dishwashers it could be a swollen check valve, not allowing the evacuation of the used dirty water.does your soap dispenser open? ... Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Asko 1996 appears "dead".....no lights flashing, won't respond to repeatedly pushing on/off button. Some water left in the bottom...siphoned it out, cleaned filters, no blockage there. Almost like it's not getting electricity, but breaker is on. Noticed this when I went to empty clean dishes, and noticed that detergent hadn't dissolved and dishes weren't clean and about a gallon of water was still in the bottom.....


Don't know if this will help, but my dishwasher has a "propeller" device above the top and bottom racks that spins while dispensing the water. If the dishes on either rack are stacked too high (i.e. if even one plate comes in contact with that ... Asko D1996SS Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

Hi, I've got a Fisher & Paykel DD603i which is very nearly 3 years old. The top drawer runs through its cycle and end with a continuous beeping, and some water left in the drwaer, although the dishes seem to be cleaned OK. I have folowed step 2 on page 7 of the manual as described in your response to a similar-ish problem, but didn't completely remove the drawer (as I wasn't sure how to get the clear plastic cover on the electrics underneath). However, at this point I had already disconnected t


Hi,Does it show Error U1 on the display. If yes, follow the below. I am hate to say, however user manual does not contain all the details.If that would have been the case, there is never a need to service manuals, bulletins or even tech's ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

I bought a used GE Triton XL d/w with no manual. It worked great but now it is not cleaning anything, when the cycle is over the soap cup is open but half of the soap is still inside of the cup. I opened the d/w during a cycle and the dishes are wet top and bottom racks so I know it's getting water but the dishes are still filthy. Why is the soap not working? It's like water is spraying everywhere but the door where the cup is!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... GE Tritonr XL GSD6260JCC Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

After running our dishes through a wash cycle we noticed there was still a lot of food stuck on the plates & glasses etc. We cleaned out the trap but due to the murky water in the well, we also pulled out the racks & removed the bottom plate. The underside was greasy and had a lot of grim stuck to it as well as the bottom of the drawer itself. We washed the filter trap, swing arm and plate in the sink. We loaded it with the dishes that previously did not come clean and ran a full cycle. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

Motor problem?? The dishwasher takes in water then the water just sits in the bottom of the unit until the end of the cycle, there is no water going through the jets so the dishes are not getting cleaned. You can hear the motor but nothing is actually happening until the end of the cycle when it just pumps the water back out again


Have you checked the pump / motor belt? ... Tecnik TDW2677 Built-in Dishwasher

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

Hello, I have a Kitchen Aid dishwasher, model KUDS30IVWH3. The dishes have not been getting as clean lately, the bottom is decent but the top rack is not getting very clean. Also, when I open the door after the cycle is done, there's a bunch of detergent at the bottom of the door and on the floor of the dishwasher, like it isn't getting sprayed all over or something. Don't know if I have to check the water intake valve or if maybe the sprayers could be partially clogged.


... KitchenAid Dishwashers

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.


Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

I have a kenmore dishwasher, model 587-1625. Noticing that are dishes didn't seem to be getting very clean. I removed the drain screen and cleaned, noticing a lot of hard water deposit. yet, it still drain. Now after cleaning it doesn't drain now what?


Check for a plugged air gap (on top of the sink) ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2246 seconds