Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Answers :

Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of the knob cover down to the pump. The other would be to make sure that the pump is working correctly and is not just draining water all the time. You can check these with a volt meter and make sure each is getting voltage
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

I have a GE potscrubber Dishwasher Model # GSD3630ZZ3WW it has been leaking from the bottom for about a week. I took the bottom off tonight and ran the dishwasher so that I could see where it is leaking from. It is not a hose but the leak seems to be coming from the back of the motor or pump fan where it goes into that plastic housing that attaches to the bottom of the dishwasher seems to be leaking in the very center of that housing where the motor shaft enters the housing. Water is just spray


... Dishwashers

Residual water remains on bottom of dishwasher. When I press the two buttons to cancel/drain it makes noise but doesn't empty and I don't hear the usual gurgling of water going down pipe. Kitchen sink is not clogged , the drain/filter is clean, there is no kink in the hose.


... Bosch 24 in. SHU43 Built-in Dishwasher

The upper spray arm does not turn. There is plenty of water volume as I have cleaned out all orifices and pipes with an air compressor and garden hose. Plenty of flow. Bottom arm rotates and sprays like a fire hose.


... Asko D3731XLHDSS Built-in Dishwasher

I have a newly installed Kitchenaide dishwasher. The copper pipe is secure under the sink and appears connected properly to the dishwasher. When I turn the shut off valve on, water begans to run from underneath the dishwasher. There is no water under the sink. The plastic hose does not seem to be the problem.


You should be able to remove the panel below the door and see where water inlet hose is connected to the solenoid valve. I'd bet that's where it's leaking since you say it's newly installed. ... Dishwashers

I have a bosch dishwasher classixx its less than a year old, the 'check water' light comes on and it doesn't complete the cycle. Water is left in the bottom unable to drain away. I have checked pipes as best i could, but couldn't locate filters or remove hose from m/c. unfortunately i have no instruction manual.. help please..


If its less than a year old why dont you contact the manufacturers service team it will still be under guarantee as the bosch guarantee is 24 months you can dowload a copy of the instruction maual free of charge from the bosch or bsh home appli ... Bosch 24 in. SRS43C12 Classixx Slim-Line Free-standing Dishwasher

Electrolux built in ESL4115 Dishwaser:- Starts the programe briefly but stops with two intermittent audible signals when you open the door the cycle has not really started and there is water at the bottom of the dishwasher(when u refer to manual says the sink spigot is blocked or water drain hose has not been correctly laid or is bent). I have had this for just over 1 year working ok up to this point, tried to see if there is a blockage, taken pipes out doesn't appear to be any blockage also th


... Electrolux Dishwashers

I have a maytag dishwasher model mdb6000aww. The water will not drain from the bottom, and I am hooked up to a disposer. I think my plastic hose is to long, because I took it of from the disposal unit. It has a little kink in it, so I am just wondering if this could be my proublem.


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain ... Maytag Dishwashers

Hi, we have an aquarius hotpoint df61 and it goes through the cycle but does not drain out the last few inches of water and the wash is not as good as it should be, have unscrewed the plastic bit under the filter thing to see if there is a blockage there but nothing, have now taken off the top and side panel to try and get to the pump, currently on it's back but hard to access underneath and not sure how to remove the solid bottom of the dishwasher..please help!


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

When I connect the water hose to the pressure washer, it leaks from the bottom. I open it and the leak comes from a white plastic receptacle that is on the left side of the pump.


... Karcher K 5.85 M Electric Pressure Washer

Leak its exactly as you described...where should I look for leaks...I can see water on the inside of the bottom tray but every pipe I can see is dry and none of the plastic parts seem to be cracked...Thanks, Tam.


Pull the unit out and tip it carefully to one side. (put some rag down first to mop up the water) then stand the unit back up.\015\012Make sure you can see the back of the unit. put some tissue paper behind the plastic pipe that runs up the bac ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1590 seconds