Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle takes over three hours. When the cycle finally finishes the dishes are not completely dry. Is there a way to adjust the timing for the cycles? I have checked the screens and they were clear.


Answers :

\015\012There are no adjustments for cycle timing. What does affect timing is temperature of the water coming into the DW. The hotter your supply water, the shorter the time to cycle, BUT if your water is too hot, the cycle time may become too short to light the NSF 'Sanitize' indicator. But since the cycle is taking so long, this is an indication that the DW's water heater is not heating the water hot enough to advance the countdown timer in a timely manner. The control logic is waiting for the temp to come up to an appropriate level to ensure adequate washing, rinsing or drying times. Likely your display is showing '1' for a long time as a symptom of this problem, as well.\015\012 -\015\012This link http://www.applianceaid.com/boschDW.html has procedures to run self-tests on various Bosch models. I suspect that you can confirm a 'heater fault' on your unit by running the self-test.\015\012 -\015\012This problem invariably relates to a 'heater fault' which has usually been traced to an open solder joint on the control board located behind the switches/indicator lights on front door. If you have a Torx driver, soldering iron & bit of solder, you can effect a repair yourself in about an hour. Otherwise, a replacement control board is required.
\015\012\015\012If you'd like to attempt replacing the control board yourself, refer to this link for part & DIY information.\015\012http://www.appliancejournal.com/appliance-parts/bosch-appliance-parts/bosch-dishwasher-control-module-266746-37/
\015\012-\015\012Else, place a service call to the tech of your choice.\015\012
\015\012  
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle takes over three hours. When the cycle finally finishes the dishes are not completely dry. Is there a way to adjust the timing for the cycles? I have checked the screens and they were clear.


\015\012There are no adjustments for cycle timing. What does affect timing is temperature of the water coming into the DW. The hotter your supply water, the shorter the time to cycle, BUT if your water is too hot, the cycle time may become too ... Bosch 24 in. SHU43 Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Our dishwasher does not complete a cycle. Regardless of what cylce it is on, part way through the the clean light blinks 7 seven times in a row and then a pause, and that repeats until the dishwasher is rebooted. What does this mean?


... KitchenAid Architect® Series II KUDT03ST Built-in Dishwasher

My dishwasher stopped at the drain cycle. I have to press cancel, and cancel(which is also the drain button) again. Then,it drains but will not complete the cycle for heated drying. Is there a easy way to fix this?


Have you checked there is nothing blocking the filter at the base of the dishwasher?\015\012\015\012Please provide the brand name and model no. of your dishwasher so that I can help you better. ... Dishwashers

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

Water will not drain out of the tub all the way and behind the front door bottom in the insulation seems to be wet. and the cycle seems to take a long time to run...thanks Dishwasher Model No. SHU9922UC/U12 goes through cycle properly but fails to drain completely.


Water does not drain from the dishwasher \015\012\015\012Check sink drain and ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

We have just purchased and installed our dishwasher. Towards the end of the cycles it has a very high pitch noise when the heated drying cycle. Is this normal, or is there something wrong? It is VERY annoying - it reminds us of a 'ringing in the ears' noise. Also - is there a listing of time for each cycle? It seems that it runs a LONG time in each cycle that I have tried - with or without any specific instruction, i.e. heated dry. Thank you.


Hello. This dishwasher is definitely not functioning properly. Call the store where you purchased it and report the problem. Because it is under warranty you have rights. You should return it [this would be my choice] or have the store sen ... Dishwashers

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

My Whirlpool ADG 7561 Dishwasher is not completing a cycle. Is completed standard rince, but when put on a full cycle it is stopping after around 10mins and constantly beeping. When I open the door, the green Start light is flashing 3 times then stopping, then 3 times again etc. Any idea what this means?


... Whirlpool ADG 7561 Dishwasher

Dishwasher bubbles I have a kenmore elite mod- 16599201 stock # 16599 , recently there has been bubbles in the washer after the wash cycle ends . I thought that I might of put detergent in the jet dry hole so I removed the dispenser and rinsed the whole thing completely clean and reinstalled it. but the bubbles are still there . I think its the jet dry not completely rinsing away. I cleaned the dishwasher with vinegar and then glisten. My water temp is slightly low as I have my water heater set


... Dishwashers

My dishwasher is leaving a film on all the dishes some of the times. Other times the appliance works fine but more and more often it is leaving a white film on all the dishes as though the rinse cycle is not working well. I have tried filling the jet dry compartment and have been using the same jet dry and detergent as always. The dishwasher is about ten years old and has been working well up to a few weeks ago. Ideas?


Check inlet water quality & whether softening salt is required. Check and fill rinse aid. refer user manual. ... Maytag 24 in. MDB3700 Built-in Dishwasher

Hi I have a Bosch sms 4012 dishwasher that was in our house when we bought it around 14yrs ago.It really has been an excellent appliance but for the past few months the control knobs have become 'sticky'and relatively hard to turn. Now the dishwasher is not completing the cycle properly by stopping intermittantly,taking almost double the cycle time to complete and not draining properly. Do you think this is just a blockage in the drainage system or something much more complex requiring a technic


... Dishwashers

I recently bought a different type of dishwashing detergent for my Frigidare dishwasher and my dishes look as if they have not been rinsed. They cycled all the way through the drying cycle so the detergent dried on and was difficult to remove. I would like some advice on whether this sounds like a detergent problem or mechanical problem before I try another load. This washer is not new. It was in the house I bought and I've only been using it for about 2 months. (I usually use Casade Liquid and


The best way to use your dishwasher is the way it was designed.\015\012if your unit has a compartment for jet dry or rinse agent then you should add and fill that compartment with rinse aid. try not to buy soap with any extra like soap with jet ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2407 seconds